Xero88 CHILLI 12 x 10 Скачать руководство пользователя страница 15

Страница: 15 / 30

Installation

Chilli Dimmer 73-853-00 Issue 8

Page 15 of 30

Figure 2 - 14: Example Chilli Net System Schematic

Chilli Network (Chilli Net)

The  following  devices  can  be
connected  to  a  Chilli  Network
system:

• Chilli Dimmer

• Chilli Control Panel

• Chilli Master Controller

• Chilli RS232 Node

• Chilli NetLink (hub)

• Spice Rack Dimmer

• Rack 6 / Install 6 Dimmers

• Frog Box.

Each  device  has  a  set  of
network  terminals  or  an  RJ12
socket  provided  for  connection
to the Chilli network.

The  cable  used  to  connect  the
various  devices  in  the  network
must  be  CAT  5  (100MHz)  FTP
cable.

Network Terminals

The  Chilli  Net  terminals  are
labelled  with  the  recommended
colours  of  the  pairs  in  CAT5
cable as follows:

Orange Pair

+12V

Blue/White

CAN-H

Blue

CAN-L

Green Pair

Brown Pair

Shield

All devices in the Chilli network
must be connected in serial. The
devices in the network can be
wired

any

order

(see

examples in Figure 2-14 above).

Termination Resistors

At  the  two  ends  of  the  Chilli
network,  a  network  termination
resistor  must  be  fitted  (see
Figure 2-14 above).

Each  Chilli  Dimmer  is  supplied
with  a  termination  resistor  fitted.
This  resistor  is  120  ohms,  0.25
Watt  and  is  connected  between
the

CAN-H

and

CAN-L

terminals.

This  resistor  must  be  removed,
unless  the  dimmer  is  at  either
end of the Chilli network.

Содержание CHILLI 12 x 10































Результаты поиска

Содержание CHILLI 12 x 10

Отзывы:

Бренды по названию

Популярные бренды

Xero88 CHILLI 12 x 10, Руководство по эксплуатации

Результаты поиска

Содержание CHILLI 12 x 10

Отзывы:

Бренды по названию

Популярные бренды