Xero88 CHILLI 12 x 10 Скачать руководство пользователя страница 19

Страница: 19 / 30

User Interface

Chilli Dimmer 73-853-00 Issue 8

Page 19 of 30

Memories

The

Chilli

Dimmer

can

programmed with up to 12
memories.

The memories are programmed
by grabbing the current outputs.

The  programmed  memories  can
then  be  played  back,  when
required.

The channel levels and fade times
for programmed memories can be
edited.

Network Mode

- memories are

recorded, played back, edited and
cleared on an area basis.

Memory Options

Select the

Memories

option from

the  top  level  options  menu,  and
press  the  ENT  key  to  enter  the
Memories  menu.  The  following
options are available:

• Record Memory
• Play Memory
• Clear Memories
• Edit Memory

Use the cursor keys to scroll
between the options, then press
the ENT key to enter the selected
option.

Record Memory

Stand Alone Mode

- This option

allows  you  to  store  the  current
output  levels  in  one  of  the  12
memories in the dimmer.

The  fade  time  can  also  be
adjusted,  if  required,  during  this
operation.

It  is  recommended  that  when
recording  memories,  the  topset
level  for  all  channels  is  set  to
100%.

Select the

Record Memory

option

from the Memories menu, and
press the ENT key. The screen
shows:

Record Memory

The cursor appears in the memory
number  field  (xx).  Unprogrammed
memories  are  indicated  by  an  ‘*’
next to the memory number.

Use the numeric keypad or cursor
keys to select the required
memory (1 - 12).

Press  the  ENT  key  to  confirm  the
memory  selection.  The  screen
shows:

Memory: xx

Fade Time: xx

The

Memory

field

for

information only and is not
editable. The cursor appears in
the

Fade Time

field.

Use the numeric keypad or cursor
keys to adjust the fade time as
required (1 - 60 seconds).

Press the ENT key to save the
fade time to the memory.

The  dimmer  will  then  grab  the
current  output  levels  and  store
them in the selected memory.

The screen will briefly show a
confirmation, and then return to
the

Record Memory

screen.

Record Memory

Network Mode

- This option

allows  you  to  store  the  current
output  levels  in  one  of  the  12
memories in the dimmer. Only the
levels  of  the  dimmer  channels
assigned to the specified area are
recorded into the memory.

The  fade  time  can  also  be
adjusted,  if  required  during  this
operation.

It  is  recommended  that  when
recording  memories,  the  topset
level  for  all  channels  is  set  to
100%.

Select the

Record Memory

option

from the Memories menu, and
press the ENT key. The screen
shows:

Area: 1

Memory: xx

The cursor is in the

Area

field.

Enter the required area number

using  the  numeric  keypad  or
cursor  keys,  then  press  the  ENT
key. If the area is valid, the cursor
moves to the Memory field.

Use the numeric keypad or cursor
keys to select the required
memory (1 - 12).

Unprogrammed memories have
an ‘*’ next to the memory number.

Press  the  ENT  key  to  confirm  the
memory  selection.  The  screen
shows:

Area xx Mem xx

Fade Time: xx

The

Area

and

Mem

fields are for

information

only.

The

cursor

appears in the

Fade Time

field.

Use the numeric keypad or cursor
keys to adjust the fade time as
required (1 - 60 seconds).

Press the ENT key to save the
fade time to the memory.

The  dimmer  will  then  grab  the
current  output  levels  for  the
selected  area  and  store  them  in
the selected memory.

The screen will briefly show a
confirmation, and then return to
the

Record Memory

screen.

Содержание CHILLI 12 x 10































Результаты поиска

Содержание CHILLI 12 x 10

Отзывы:

Похожие инструкции для CHILLI 12 x 10

Бренды по названию

Популярные бренды

Xero88 CHILLI 12 x 10, Руководство по эксплуатации

Результаты поиска

Содержание CHILLI 12 x 10

Отзывы:

Похожие инструкции для CHILLI 12 x 10

Бренды по названию

Популярные бренды