Xavant STIMPOD MMS460 Скачать руководство пользователя страница 7

Recommended separation distances between

portable and mobile RF communications equipment and the STIMPOD NMS460

The STIMPOD NMS460 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the STIMPOD NMS460  can 
help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the STIMPOD NMS460 as 
recommended below, according to the maximum output power of the communications equipment.

Rated maximum output power

W

Separation distance according to frequency of transmitter 

m

150 kHz to 80 MHz

Not applicable

80 MHz to 800 MHz 

d = 1,2    

800 MHz to 2,5 GHz 

d = 2,3   

0,01 

-

0,12

0,23

0,1 

-

0,38

0,73

-

1,2

2,3

10 

-

3,8

7,3

100 

-

12

23

For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency 
of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1  

At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2  

These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Guidance and manufacturers declaration – electromagnetic immunity – for equipment and systems that are non- 

life supporting

The STIMPOD NMS460  is intended for use in the electromagnetic environment specified below. The customer or the user of the STIMPOD NMS460  should ensure that it is used in such 
an environment

Immunity Test

IEC 60601 test level

Compliance level

Electromagnetic environment - guidance

Radiated immunity
80MHz - 2.5GHz

80MHz – 1GHz @ 3V/m & 
10V/m
1GHz – 2.5GHz @ 10V/m

80MHz – 1GHz @ 3V/m & 
10V/m
1GHz – 2.5GHz @ 10V/m

Portable and mobile RF communications equipment can affect MEDICAL
ELECTRICAL EQUIPMENT and should be used no closer to any part of the 
equipment, including cables, than the recommended separation distance.

vi

Содержание STIMPOD MMS460





















Отзывы: