Xantrex PV-45208 Скачать руководство пользователя | Manualshive

Страница: 30 / 41

background image

SECTION 6
PREVENTATIVE MAINTENANCE

PV-45208 Photovoltaic Inverter

Operation and Maintenance Manual

Copyright 2002, Xantrex Technology Inc.

DOCUMENT: 151710

6-1

PERIODIC MAINTENANCE

Xantrex Technology recommends that the following preventative maintenance be carried out on the
PV-45208:

Monthly intervals or as required:

Aluminum Extrusion Heatsink

Accumulation of dirt and debris on the aluminum extrusion heatsink and fan shroud will de-
crease the ability to transfer heat, which can cause the PV-45208 to shutdown on over-tempera-
ture alarms. Inspect the aluminum extrusion heatsink and fan shroud for accumulation of dirt
and debris. Remove enclosure panels and clean if debris is present.

Fan Operation

Verify proper operation of the heatsink cooling fan, located within the lower enclosure. The fan
operates when the K1 contactor is closed. Remove any debris from the fan and finger guard.

Six month intervals:

(See Isolation Procedure and perform prior to the following)

Enclosure Seals

Inspect the enclosure access panel seal. If damaged, replace with equivalent closed cell foam
gasket. Call your Xantrex Technology distributor for factory replacements or specifications.

Electrical Connections

Inspect the condition of all wiring within the PV-45208. Inspect all wire crimps and connec-
tions for damage caused from high temperature. Check for corrosion. Replace any damaged
wires. Verify all mechanical connections are sufficiently tightened. Verify all conduction sur-
faces are clean and free of corrosion.

Mechanical electrical connections will loosen over time. This is caused primarily by thermal
cycling during normal operation. As connections loosen, electrical impedance will increase at
the connection, eventually leading to fire and component damage. It is critical to check all
electrical connections every six months.

Enclosure

Access the enclosure and remove any accumulated dirt and debris. Vacuum enclosure whenever
dust or dirt is present.

ISOLATION PROCEDURE

The following procedure should be followed to de-energize the PV-45208 for maintenance:

«
...
28
29
30
31
32
...
»

Содержание PV-45208










































Отзывы:

Нет отзывов

Похожие инструкции для PV-45208

Бренд: Ramsey Electronics Страницы: 20

Бренд: Patton electronics Страницы: 16

Бренд: Danfoss Страницы: 36

CO-SinusUPS-400W

Бренд: Adler Power Страницы: 4

ALL-USB-RS422/485

Бренд: Allnet Страницы: 6

Бренд: Badger Meter Страницы: 12

Бренд: FONESTAR Страницы: 9

Бренд: Renkforce Страницы: 4

STEVAL-CTM004V1

Бренд: STMicroelectronics Страницы: 40

4i4o + Merge 2i4o

Бренд: Prodipe Страницы: 16

Бренд: M2TECH Страницы: 49

Бренд: V-TAC Страницы: 43

Бренд: Lika Страницы: 2

SUNNY BOY STORAGE 2.5

Бренд: SMA Страницы: 110

Бренд: APsystems Страницы: 23

Бренд: Rheem Страницы: 32

Бренд: Ulvac Страницы: 26

Бренд: RoboGuard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды