Xantrex PV-45208 Скачать руководство пользователя

Страница: 12 / 41

SECTION 3
INSTALLATION AND INITIAL TURN-ON

PV-45208 Photovoltaic Inverter

Operation and Maintenance Manual

DOCUMENT: 151710

3-5

The following wires for connecting the PV-45208 to external devices are not provided by Xantrex
Technology: (See wiring diagram on page 3-6.)

•

3-Phase 208 VAC inverter output to terminals of the 208 VAC primary side of isolation trans-
former.

The neutral must be left floating. Ground loops will exist when the inverter starts

switching, which will cause the inverter to shut down due to phase over-currents and will
result in damage to the PV-45208. Also, insure that this neutral is not bonded to the isola-
tion transformer frame.

•

System electrical ground to the isolation transformer chassis ground.

•

Isolation transformer grid side terminals to line circuit breaker (or the AC disconnect switch if
present).

•

PV frame ground to PV-45208 enclosure chassis ground stud.

•

PV-45208 enclosure chassis ground stud to the electrical distribution system ground.

•

PV+ to the inverter enclosure terminal block TBDC+.

•

PV- to the inverter enclosure terminal block TBDC-.

•

PV neutral if connecting a bipolar PV array.

Install all wires listed above. Refer to the following wiring diagram and the system schematics in
Section 7 for more detailed terminal locations.

Содержание PV-45208










































Результаты поиска

Содержание PV-45208

Отзывы:

Похожие инструкции для PV-45208

Бренды по названию

Популярные бренды

Xantrex PV-45208, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PV-45208

Отзывы:

Похожие инструкции для PV-45208

Бренды по названию

Популярные бренды