Xantrex Freedom SW 230V 815-3524-02 Скачать руководство пользователя

Страница: 21 / 104

975-0696-01-01

System Components

The Xanbus-enabled designation (see below) means that this
product works on a Xanbus network. Xanbus-enabled products are:
•

Simple to operate and routine tasks are automated.

•

Controlled by software that eliminates analog signalling errors.

•

Less susceptible to interference and line loss.

•

Upgradable through new software releases.

For detailed instructions and a complete list of Xanbus-enabled
devices, visit

www.xantrex.com.

Xanbus-enabled Products and Accessories

Xanbus-enabled Products (Shown above)

Product Number/s

Xanbus System Control Panel (SCP)

809-0921

Xanbus Automatic Generator Start (AGS)

809-0915

3-ft network cable (0.9 m)

809-0935

25-ft network cable (7.6 m)

809-0940

75-ft network cable (22.9 m)

809-0942

Accessories (Shown above)

Product Number/s

Freedom SW On/Off Switch (Not shown)

808-9002

Inverter drip shield

808-9004

SCP

AGS

25-ft cable

75-ft cable

3-ft cable

Inverter drip shield

FSW 230V Owners Guide.book Page 7 Tuesday, August 7, 2018 9:38 AM

Содержание Freedom SW 230V 815-3524-02









































































































Результаты поиска

Содержание Freedom SW 230V 815-3524-02

Отзывы:

Похожие инструкции для Freedom SW 230V 815-3524-02

Бренды по названию

Популярные бренды

Xantrex Freedom SW 230V 815-3524-02, Руководство пользователя

Результаты поиска

Содержание Freedom SW 230V 815-3524-02

Отзывы:

Похожие инструкции для Freedom SW 230V 815-3524-02

Бренды по названию

Популярные бренды