background image

31

30

You cannot store any functions under the
following keys:

L

earn

Setup
T V
VCR
Cable
SAT
CD
AUX1

AUX2
X10
Timer
Enter
Shift
Shift Learn
Shift Setup
Shift TV

Shift VCR
Shift Cable
Shift SAT
Shift CD
Shift AUX1
Shift AUX2
Shift X10
Shift Timer

You cannot store 

store two products under the

same key using shift, i.e. you can’t enter the
3 digit code for a VCR and then press shift
and enter another 3 digit code for another
VCR. But you can learn 

learn a second product

using SHIFT as follows.

e.g. For two VCRs:

Press SETUP, VCR, then enter the 3 digit
code for your first VCR (see page 14 for
more details).

For VCR2:

Press SETUP, VCR, LEARN.

Then press SHIFT, then Play (on the
PUR08) then Play (on the original VCR
remote).

Then SHIFT, then Stop (on the PUR08)
then Stop (on the original VCR remote),
etc.

Then Enter.

Then to access each VCR:

Press VCR on the PUR08 and the appro-
priate key on the PUR08 to access the first
VCR.

Press VCR and then Shift, and then the
appropriate key to access the second VCR.
You can keep pressing keys and you will
stay in the “shifted mode” for about 10
seconds. You will time out of the shifted
mode about 10 seconds after the last key is
pressed.

6.

Press the button
on your existing
remote that you
want to learn. Hold
the button until the
LED on the
Learning Remote
blinks off.

7.

Repeat steps 5 and 6 for each button
you want to learn.

8.

When you’ve
finished learning
all the keys, press
ENTER.

Notes:

Notes:

Make sure you have fresh batteries in both
remotes before learning.
Take care not to move either remote while
pressing the buttons.
Experiment with the distance between the
remotes if you have a problem learning.
Some remotes do not have their LED in
the center so you might need to
experiment with the side-to-side position
of the remotes relative to each other.
Do not sit directly under an incandescent
lamp while teaching the Learning Remote.
In most cases you will hold the button on
the remote you are learning from until the
LED goes out on the Learning Remote. In
some cases however, you might find that
the LED on the Learning Remote doesn’t
go out until you release the key on the
remote you are learning from.
Use buttons L1 and L2 to learn codes for
which the Learning Remote does not have
a corresponding button.
If you have problems learning keys, try a
Master Reset (Page 12) and then try
learning them again.

Содержание PUR08




















Отзывы: