background image

WARNING 

CONSTANT EXPOSURE TO HIGH OR LOW TEMPERATURES AND HIGH HUMIDITY MAY REDUCE 

BATTERY LIFE. 

 

How to Set up and Interconnect Wireless Alarms 

All X-Sense Link

+

 wireless interlinked alarms contain a built-in RF module that enables you to wirelessly connect 2 or 

more interlinked alarms and create an interlinked network. When one unit is triggered, all interconnected alarms will 

sound. The X-Sense Link

series contain wireless interlinked smoke alarms, wireless interlinked carbon monoxide 

alarms, and wireless interlinked combination smoke and carbon monoxide alarms. This model is designed to be 

wirelessly interlinked with other X-Sense Link

+

 alarms, but is not designed to communicate with wireless interlinked 

alarms from other manufacturers.   

The  X-Sense  Link

+

  wirelessinterlinked  alarms  in  one  multi-pack  have  already  been  interconnected,  and  the 

alarms  in  each  multi-pack  have  their  own  independent  interlinked  network.  If  you  have  more  than  one 

multi-pack, you will need to connect them all to the same network. Choose one multi-pack as your base network 

and connect the other multi-packs to it.   

NOTE: The following instructions regarding wireless interconnection are applicable to the X-Sense Link

+

 

wirelessinterlinked alarms only.   

 

How to Interconnect   

1.

 

Make sure you only work with 2 units at a time, and make sure that they are both turned on to ensure successful 

connection. 

NOTE: Install the batteries correctly to turn on CO03D-W. To learn how to turn on different models of wireless 

interlinked alarms, please refer to their specific user manuals for more details. 

 

2.

 

Quickly press the TEST/HUSH button on one of the 2 units 4 times; it will beep once and the red LED will flash 

slowly, indicating it has entered pairing mode and is waiting for a new unit to be added. Quickly press the 

TEST/HUSH button on the other unit twice; it will beep once and the red LED will flash rapidly, indicating it is 

searching for a device to connect to.   

3.

 

After the search is successfulandan interconnected group is created, both units will beep once and automatically exit 

the interconnection mode. At this point, both units will only flash once 60 seconds, indicating they are in normal 

standby mode.   

4.

 

If you want to connect a third alarm to this group, first activate a new device according to its operating instructions, 

andthen quickly press the TEST/HUSH button on either of the 2 previously interconnected units 4 times. This unit 

will beep once, and the red LED will flash slowly, indicating it is ready to add a new device to the network. Next, 

quickly press the TEST/HUSH button on the new unit twice, and the red LED will flash rapidly as it searches for a 

network to connect to. After the third unit successfully joins the interconnected network, both units will beep once 

and automatically exit the interconnection mode.   

Содержание Link+ CO03D-W




















Отзывы: