background image

TEST/HUSH Button 

The TEST/HUSH button is used to test the unit's electronics and to silence the unit during an alarm. When testing the 

alarm (which should be done weekly), press the test button and you will hear a short beep, indicating that the alarm has 
entered the test mode. Please refer to the “Alarm Test” section for further information. The alarm will revert back to 

standby mode after testing.   

 

Note: After the test has begun, the alarm will sound, and the red LED will flash. This does NOT indicate that CO is 

present. If you press the test button during an alarm state, the unit will enter silence mode. 

 

 

CO Alarm Levels 

This X-Sensecarbon monoxide alarm is programmed to sound an alarm at the following CO concentrations within the 

time periods listed: 

70 ppm for 60-240 minutes,   

150 ppm for 10-50 minutes,   

and 400 ppm for 4-15 minutes 

When CO is detected and the alarm sounds, the CO concentration will be displayed on the LCD and a blue backlight will 

be lit. The red LED will flash and the alarm will issue 4 short beeps, repeating the cycle every 5.8 seconds.

 

 

CO Concentration and Symptoms 

The table below shows the effects of different levels of CO poisoning on the body: 

Parts per million (PPM) 

Effects on adults 

100 

Slight headache, nausea, fatigue (flu-like symptoms) 

200 

Dizziness and headache within 2-3 hours 

400 

Nausea, frontal headache, drowsiness, confusion and rapid 

heart rate. Risk to life after over 3 hours of exposure 

800 

Severe headaches, convulsions, vital organ failures. Death 

possible within 2-3 hours 

Содержание Link+ CO03D-W




















Отзывы: