want to use to start the tool by tapping the ‘Ignore’ button to the right of that input. This will
toggle between ‘H’,’L’, and ‘
what the controller is currently seeing on that input. Press the yellow
save changes if desired.
Note: Ensure the driver will require the start signal
driver is meant to run. If the start signal is removed in the middle of a rundown, the driver will
stop and give a ‘sequence aborted’ error
Note: It is recommended that the remote start command
other commands such as a task select, a signal delay of 300ms or greater is recommended for
optimal system performance.
•
REVERSE ROTATION SELECT:
o
Tap the ‘Setup’ Button
o
Make sure the task shown at
o
Tap the ‘Inputs’ Button
o
Tap the arrow button on the
Select the ‘Reverse’ button on the left side of the screen. You should now see a column of
buttons appear in the chart next to each input number. You may now select which input you
want to use to define left hand rotation in the tool by tapping the ‘Ignore’ button to the right of
that input. This will toggle between ‘H’,’L’, and ‘Ignore’ with each tap. T
of this button shows what the
button at the top and save changes if desired.
Note: Ensure the reverse settings on the Task’s ‘Setup’ screen are set to the desire
settings (rotation direction, speed,
selecting the reverse function must be active as well as the input for the remote start
Highlight
Page 22
want to use to start the tool by tapping the ‘Ignore’ button to the right of that input. This will
toggle between ‘H’,’L’, and ‘Ignore’ with each tap. The picture to the right of this button shows
is currently seeing on that input. Press the yellow [<<] button at the top and
Ensure the driver will require the start signal to be active the entire time the
driver is meant to run. If the start signal is removed in the middle of a rundown, the driver will
stop and give a ‘sequence aborted’ error on the ‘Run Tool’ screen.
It is recommended that the remote start command not be given simultaneously to
other commands such as a task select, a signal delay of 300ms or greater is recommended for
optimal system performance.
ROTATION SELECT:
From the ‘Run Tool’ Screen:
Tap the ‘Setup’ Button
Make sure the task shown at the top is the one to be programmed.
Tap the ‘Inputs’ Button
Tap the arrow button on the bottom next to ‘Setup Bolt(s)’ so that ‘Setup Misc’ appears.
’ button on the left side of the screen. You should now see a column of
ar in the chart next to each input number. You may now select which input you
hand rotation in the tool by tapping the ‘Ignore’ button to the right of
that input. This will toggle between ‘H’,’L’, and ‘Ignore’ with each tap. The picture to the right
of this button shows what the controller is currently seeing on that input. Press the yellow
button at the top and save changes if desired.
Ensure the reverse settings on the Task’s ‘Setup’ screen are set to the desire
, speed, and power).
In order for the reverse to function, the input
selecting the reverse function must be active as well as the input for the remote start
want to use to start the tool by tapping the ‘Ignore’ button to the right of that input. This will
Ignore’ with each tap. The picture to the right of this button shows
button at the top and
to be active the entire time the
driver is meant to run. If the start signal is removed in the middle of a rundown, the driver will
not be given simultaneously to
other commands such as a task select, a signal delay of 300ms or greater is recommended for
so that ‘Setup Misc’ appears.
’ button on the left side of the screen. You should now see a column of
ar in the chart next to each input number. You may now select which input you
hand rotation in the tool by tapping the ‘Ignore’ button to the right of
he picture to the right
is currently seeing on that input. Press the yellow [<<]
Ensure the reverse settings on the Task’s ‘Setup’ screen are set to the desired
In order for the reverse to function, the input
selecting the reverse function must be active as well as the input for the remote start
