12
Technical Support: [email protected] US: +1 866 677 0053 EU: +44 (0) 1793 230 343
MAINTENANCE AND PRODUCT SER
VICE
• STANDARD (or “category 1”) HDMI cables perform
at speeds of 75Mhz or up to 6.75Gbps, which is the
equivalent to a 720p/1080i signal – These HDMI cables
are NOT recommended.
• All WyreStorm equipment support HIGH-SPEED
(or “category 2”) HDMI cables that have been tested
to perform at speeds of 340Mhz or up to 10.2Gbps,
which is the highest bandwidth currently utilised over
an HDMI cable and can successfully handle 1080p
signals including those at increased colour depths and/
or increased refresh rates from the Source. High-Speed
cables are also able to accommodate higher resolution
displays, such as WQXGA cinema monitors (resolution of
2560 x 1600).
What about screens with different resolution
capabilities?
When sending a signal point to point a TV will
communicate it’s capabilities to the source, then the
source will output a suitable signal that compatible (i.e.
1080p Stereo audio). If you were to use a matrix switch
with three 1080p screens and one 1080i screen, the
resultant image would be1080i across all screens. The
matrix switches do not scale per output but instead
negotiate with the source a signal that all screens are
capable of supporting.
How does the Trasnmission device handle HDCP?
HDCP (High Definition Copyright Protection) is a feature
built in to HDMI devices to prevent theft of or illegal
distribution of HD content. Unlike competing products,
WyreStorm equipment are legal and comply with HDCP
regulations.
They do this by assigning a “key” to any display
connected to the device. HDCP “keys” are assigned to a
display when connected to a HDMI device normally. This
doesn’t change when connecting to an extender, receiver
or matrix switch; rather keys are duplicated or more are
assigned.
I can get 1080i but not 1080p at a TV location
Firstly ensure that both the source is capable of outputting
1080p and that the TV is Full HD 1080p screen. If this is
the case then the AMP, 70 metre receiver or PP Matrix
may require EDID management setting up using the DIP
switches. This useful feature provides a successful “send
and receive” to ensure swift and stable EDID negotiation
between the source and display. See Troubleshooting
section for more tips on problem solving.
I cannot get a signal from my A/V receiver along a
Cat 5e extender set
Check to ensure that the A/V Receiver isn’t adding CEC
(HDMI Control Protocol) to the outgoing signal, this can
sometimes have an effect on the HDMI signal.
12. Product Service
Clean this unit with a soft, dry cloth only. Never use
alcohol, paint thinner or other harsh chemicals.
11. Maintenance
1. Damage requiring service:
This unit should be
serviced by a qualified service personnel if:
• The DC power supply or AC adaptor has been
damaged.
• Objects or liquid have gotten into the unit.
• The unit has been exposed to rain.
• The unit does not operate normally or exhibits a marked
change in performance.
• The unit has been dropped or the cabinet damaged.
2. Servicing Personnel:
Do not attempt to service the
unit beyond that described in these operating instructions.
Refer all other servicing to authorised servicing personnel.
3. Replacement Parts:
When parts need replacing,
ensure parts approved by the manufacturer are used
– either those specified by the manufacturer or parts
possessing the same characteristics as the original parts.
Be aware – unauthorised substitutes may result in fire,
electric shock, or other hazards and will invalidate your
warranty.
4. Safety Check:
After repairs or service, ask the
service personnel to perform safety checks to confirm
the unit is in proper working condition.When shipping the
unit, carefully pack and send it prepaid, with adequate
insurance and preferably in the original packaging. Please
include a document or letter detailing the reason for return
and include a daytime telephone number and/or email
address where you can be contacted.
