WPI SI-HTB Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 48

WPI SI-HTB Скачать руководство пользователя страница 43

SI-MT/SI-MKB/SI-HTB

WORLD PRECISION IN STRU MENTS

39

2. Press

the

Up

or

Down

button to adjust the backlight level.

3. Press

the

Display

button to save the confi guration and return to the normal display.

Enabling/Disabling the Alarms

By default the alarms are disabled. When enabled, the unit will emit a beep when an
alarm state occurs.

1. Press

the

Setup

button until “CH1 Alarm” or “CH2 Alarm” appears on the screen.

CH1 Alarm
DISABLED

Fig. 43 By default the alarms are disabled.

2. Press

the

Up

or

Down

button to enable or disable the alarm.

3. Press

the

Display

button to save the confi guration and return to the normal display.

Using the USB Port Output

The USB port can be used to connect to a computer to log the temperature history. In
order to communicate with the computer, a terminal emulation program is required.
Several third party options are available, including: Hyperterminal, Real Term (realterm.
sourceforge.net) or Cool Term (freeware.the-meiers.org).

1. When you use a standard USB cable to connect the

SI-TCM2

to your computer, the

computer will automatically install the necessary drivers.

2. Set up your terminal emulation program using the following parameters:

•

Baud rate: 38400 Bd

•

Data:

8 bits, (1 start, 1 stop)

• Parity: None

3. The comma delimited, output fi le logs the temperature 10 times a second.

«
...
41
42
43
44
45
...
»

Содержание SI-HTB

















































Отзывы:

Нет отзывов