manualshive.com logo in svg

WPI SI-HTB, Инструкция по эксплуатации, Страница: 10 / 48

Поделиться
Скачать
WPI SI-HTB Скачать руководство пользователя страница 10

SI-H Muscle Testers

6

WORLD PRECISION IN STRU MENTS

NOTE

: The 16 plugs marked with A or B are for future development. They are not used at 

this time.

SI-BAM21-LCB

The  

SI-BAM21-LCB 

KG  Optical Force Transducer  Amplifi er is used in conjunction with the 

SI-H tissue bath and muscle physiology systems. The 

SI-BAM21-LCB

 powers the force 

transducer and converts the output of the transducer to an amplifi ed  analog voltage 
that is proportional to the force applied to the force transducer. The output signal can be 
multiplied by a factor of 1, 2, 5 or 10 to provide better resolution for a minimal change in 
applied force. 

NOTE

: An optional factory setting increases the multiplier by a factor of 10, allowing the 

signal to be multiplied by 10, 20, 50 and 100.

NOTE

: The  

SI-BAM21-LC

 is the standalone version of this optical force transducer 

amplifi er.

Features

The 

SI-BAM21-LCB

 amplifi er works with KG optical force transducers to:

• 

Generate an analog output (-10VDC to +10VDC) that is proportional to the force 
applied to the tissue sample.

• 

Supply a DC voltage that powers the KG force transducer to which it is 
connected.

How the Amplifi er Works

In a typical setup, a muscle is held by a   force transducer. The  force transducer is 
connected to the 

SI-BAM21-LCB

. As the muscle contracts or releases, the  force transducer 

converts the force into an electrical current signal which is proportional to the force 
applied to the force transducer. The 

SI-BAM21-LCB

 converts the current signal into a 

voltage signal that can be displayed on the screen of the recording device.

Before initiating an experiment, the 

SI-BAM21-LCB

 must fi rst be  zeroed. This sets the 

 baseline for measurements to follow.

The output signal is  buffered and multiplied by 1, 2, 5 or 10, depending on the  Gain 
switch setting on the front panel of the amplifi er module. The X10 setting is useful when 
output signals are extremely small. Finally, the force proportional signal is sent through 
the output amplifi er circuit. 

The analog output has a range of –10V to +10V that drives a  data acquisition system, 
multimeter or oscilloscope.

Notes and Warnings

NOTE

: The 

SI-BAM21-LCB

 is only designed for use with KG optical force transducers. 

Use with any other type of transducer may cause damage to either the transducer or the 
amplifi er or both.

Содержание SI-HTB

















































Отзывы:

Нет отзывов