
14
OpERATINg INSTRuCTIONS
note:
Before using the tool, read the
instruction book carefully.
InTEnDED USE:
The tool is intended for ripping and cross-cutting
wood and other materials in straight cutting lines,
while resting firmly on the work piece.
ASSEMBLy AND OpERATION
Action
Figure
Saw blade assembly and
removing
See Fig. A
Safety on/off switch
See Fig. B
Cross and rip cutting
See Fig. C1, C2
Using the laser light feature
See Fig. D1,D2
Replacing laser batteries
See Fig. E1-E3
Parallel guide
See Fig. F1, F2
Cutting depth adjusting
See Fig. G1,G2
Cutting angle adjusting
See Fig. H
Pocket cutting
See Fig. I1,I2
Sawdust removal
See Fig. J
wORKINg HINTS FOR yOuR
TOOL
If your power tool becomes too hot, please run
your circular saw no load for 2-3 minutes to cool
the motor. Avoid prolonged usage at very low
speeds.
Protect saw blades against impact and shock.
Cutting with extreme force can significantly
reduces the performance capability of the tool
and reduces the service life of the saw blade.
Sawing performance and cutting quality depend
essentially on the condition and the tooth count
of the saw blade. Therefore, use only sharp saw
blades that are suited for the material being cut.
Choice of blades: 24 teeth for general work,
approx. 40 teeth for finer cuts, more than 40
teeth for very fine cuts into delicate surfaces,
diamond for tile, cement board, etc.
Only use saw blades recommended.
MAINTAIN TOOLS wITH
CARE
remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and if damaged, have repaired
by authorized service facility. Your power tool
requires no additional lubrication or maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to
clean your power tool. Wipe clean with a dry
cloth. Always store your power tool in a dry place.
Keep the motor ventilation slots clean. Keep all
working controls free of dust.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a
hazard.
Periodically clear dust and chips from guard and
base to ensure proper performance.
ENVIRONMENTAL
pROTECTION
This product has been marked with a
symbol relating to removing electric and
electronic waste. This means that this
product shall not be discarded with household
waste but that it shall be returned to a collection
system which conforms to the European
Directive 2002/96/CE. It will then be recycled or
dismantled in order to reduce the impact on the
environment. Electric and electronic equipment
can be hazardous for the environment and for
human health since they contain hazardous
substances.
Содержание WU427.1
