Worx WU427.1 Скачать руководство пользователя страница 11

11

undamaged wheel. After inspecting and 
installing the wheel, position yourself and 
bystanders away from the plane of the 
rotating wheel and run the power tool at 
maximum no load speed for one minute. 

Damaged wheels will normally break apart 
during this test time.

j)  Wear personal protective equipment. 

Depending on application, use face 
shield, safety goggles or safety glasses. 
As appropriate, wear dust mask, hearing 
protectors, gloves and shop apron capable 
of stopping small abrasive or workpiece 
fragments. 

The eye protection must be 

capable of stopping flying debris generated 
by various operations. The dust mask or 
respirator must be capable of filtrating 
particles generated by your operation. 
Prolonged exposure to high intensity noise 
may cause hearing loss.

k)  Keep bystanders a safe distance away from 

work area. Anyone entering the work area 
must wear personal protective equipment. 

Fragments of workpiece or of a broken 
wheel may fly away and cause injury beyond 
immediate area of operation.

I)  Hold the power tool by insulated gripping 

surfaces only, when performing an 
operation where the cutting accessory 
may contact hidden wiring or its own cord. 

Cutting accessory contacting a “live” wire 
may make exposed metal parts of the power 
tool “live” and could give the operator an 
electric shock.

m)  Position the cord clear of the spinning 

accessory. 

lf you lose control, the cord may 

be cut or snagged and your hand or arm may 
be pulled into the spinning wheel.

n)   never lay the power tool down until the 

accessory has come to a complete stop. 

The spinning wheel may grab the surface and 
pull the power tool out of your control.

o)  Do not run the power tool while carrying 

it at your side. 

Accidental contact with the 

spinning accessory could snag your clothing, 
pulling the accessory into your body.

p)  regularly clean the power tool’s air vents. 

The motor’s fan will draw the dust inside 
the housing and excessive accumulation of 
powdered metal may cause electrical hazards.

q)  Do not operate the power tool near 

flammable materials. 

Sparks could ignite 

these materials.

r)  Do not use accessories that require liquid 

coolants. 

Using water or other liquid coolants 

may result in electrocution or shock.  

FuRTHER SAFETy 

INSTRuCTIONS FOR 

ABRASIVE CuTTINg-OFF 

OpERATIONS

Kickback and related warnings

Kickback is a sudden reaction to a pinched or 
snagged rotating wheel. Pinching or snagging 
causes rapid stalling of the rotating wheel which 
in turn causes the uncontrolled power tool to be 
forced in the direction opposite of the wheel’s 
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or 
pinched by the workpiece, the edge of the wheel 
that is entering into the pinch point can dig into 
the surface of the material causing the wheel to 
climb out or kick out. The wheel may either jump 
toward or away from the operator, depending on 
direction of the wheel’s movement at the point of 
pinching. Abrasive wheels may also break under 
these conditions.
Kickback is the result of power tool misuse and/
or incorrect operating procedures or conditions 
and can be avoided by taking proper precautions 
as given below.

a)  Maintain a firm grip on the power tool 

and position your body and arm to allow 
you to resist kickback forces. Always use 
auxiliary handle, if provided, for maximum 
control over kickback or torque reaction 
during start-up.

 The operator can control 

torque reactions or kickback forces, if proper 
precautions are taken.

b)  never place your hand near the rotating 

accessory. 

Accessory may kickback over your 

hand.

C) Do not position your body in line with the 

rotating wheel. 

Kickback will propel the tool 

in direction opposite to the wheel’s movement 
at the point of snagging.

d)   Use special care when working Corners, 

sharp edges etc. Avoid bouncing and 
snagging the accessory. 

Corners, sharp 

edges or bouncing have a tendency to snag 
the rotating accessory and cause loss of 
control or kickback.

e)   Do not attach a saw chain, woodcarving 

Содержание WU427.1





















Отзывы: