Worx WU427.1 Скачать руководство пользователя страница 10

10

SAFETy INSTRuCTIONS 

FOR SAwS wITH INNER 

pENDuLuM guARD

Lower Guard Function
a)  Check lower guard for proper closing 

before each use. Do not operate the saw 
if lower guard does not move freely and 
close instantly. never clamp or tie the 
lower guard into the open position.

 If saw 

is accidentally dropped, lower guard may be 
bent.Raise the lower guard with the retracting 
handle and make sure it moves freely and 
does not touch the blade or any other part, in 
all angles and depths of cut.

b)  Check the operation of the lower guard 

spring. If the guard and the spring are not 
operating properly, they must be serviced 
before use.

 Lower guard may operate 

sluggishly due to damaged parts, gummy 
deposits, or a build-up of debris.

c)  Lower guard may be retracted manually 

only for special cuts such as "plunge cuts" 
and "compound cuts." raise lower guard 
by retracting handle and as soon as blade 
enters the material, the lower guard must 
be released.

 For all other sawing, the lower 

guard should operate

 

automatically.

d)  Always observe that the lower guard is 

covering the blade before placing saw 
down on bench or floor. 

An unprotected, 

coasting blade will cause the saw to walk 
backwards, cutting whatever is in its path. Be 
aware of the time it takes for the blade to stop 
after switch is released.

ADDITIONAL SAFETy 

RuLES FOR yOuR 

CIRCuLAR SAw

1.   Always wear a dust mask, hearing protection 

and eye protection.

2.  Only use saw blades recommended in the 

specification.

3.  Do not use any abrasive wheels.
4.  Use only blade diameter(s) in accordance with 

the markings.

SAFETy INSTRuCTIONS 

FOR ABRASIVE 

CuTTINg-OFF OpERATIONS

Cut-off machine safety warnings
a)  The guard provided with the tool must 

be securely attached to the power tool 
and positioned for maximum safety, so 
the least amount of wheel is exposed 
towards the operator. Position yourself 
and bystanders away from the plane of the 
rotating wheel. 

The guard helps to protect 

operator from broken wheel fragments and 
accidental contact with wheel.

b)  Use only diamond cut-off wheels for your 

power tool. 

Just because an accessory can 

be attached to your power tool, it does not 
assure safe operation.

C) The rated speed of the accessory must 

be at least equal to the maximum speed 
marked on the power tool. 

Accessories 

running faster than their rated speed can 
break and fly apart.

d)  Wheels must be used only for 

recommended applications. For example: 
do not grind with the side of cut-off wheel. 

Abrasive cut-off wheels are intended for 
peripheral grinding, side forces applied to 
these wheels may cause them to shatter.

e)  Always use undamaged wheel flanges that 

are of correct diameter for your selected 
wheel. 

Proper wheel flanges support the 

wheel thus reducing the possibility of wheel 
breakage.

f)  Do not use worn down reinforced wheels 

from larger power tools. 

Wheels intended 

for a larger power tool are not suitable for the 
higher speed of a smaller tool and may burst.

g)  The outside diameter and the thickness of 

your accessory must be within the capacity 
rating of your power tool.

 Incorrectly sized 

accessories cannot be adequately guarded or 
controlled.

h)  The arbour size of wheels and flanges 

must properly fit the spindle of the power 
tool. 

Wheels and flanges with arbour holes 

that do not match the mounting hardware of 
the power tool will run out of balance, vibrate 
excessively and may cause loss of control.

i)  Do not use damaged wheels. Before 

each use, inspect the wheels for chips 
and cracks. If power tool or wheel is 
dropped, inspect for damage or install an 

Содержание WU427.1





















Отзывы: