15
Cordless Lawn Mower
EN
4. If a grass bag is used during the fast growing
season, the grass may tend to clog up at the
discharge opening. Release bail handle to turn
mower “OFF” and remove the safety key. Remove
the grass bag and shake the grass down to the
back end of the bag. Also clean out any grass or
debris which may be packed around the discharge
opening. Replace the grass collection bag.
5. If mower should start to vibrate abnormally, release
bail handle to turn mower “OFF” and remove safety
key. Check immediately for cause. Vibration is a
warning of trouble. Do not operate mower until a
service check has been made.
6. ALWAYS RELEASE BAIL HANDLE TO TURN
MOWER “OFF” AND REMOVE SAFETY KEY WHEN
LEAVING IT UNATTENDED EVEN FOR A SHORT
PERIOD OF TIME.
CUTTING AREA
The cutting area can be affected by several factors,
such as cutting height, lawn humidity, grass length
and density. Besides, starting and stopping the mower
too many times during operation will reduce the
cutting area.
The table below gives the relationship between cutting
conditions and cutting area.
Cutting Height
Cutting Area
(maximum)
Cutting 7 cm to 5 cm
200m
2
(4.0Ah battery)
TIPS:
1) It is recommended to mow your lawn more
frequently, walk at normal pace, and not to start/
stop the mower too often during operation.
2) For best performance, please ensure use two fully
charged battery packs at the same time and always
cut off 1/3 or less of the grass height.
3) Walk slowly when cutting long grass, so as to have
more effective cutting and properly discharge the
clippings.
4) Avoid cutting wet grass, otherwise it will stick to the
underside of the deck and the clippings cannot be
collected or discharged properly.
5) A higher cutting height shall be applied to new or
thick grass and it will extend the battery duration.
6. MAINTENANCE
WARNING:
Stop the mower, remove the safety
key and battery before removing the grass
collection bag.
NOTE:
To ensure long and reliable service, perform the
following maintenance procedures regularly. Check for
obvious defects such as a loose, dislodged or a damaged
blade, loose fittings, and worn or damaged components.
Check that the covers and guards are all undamaged and
are correctly attached to mower. Carry out any necessary
maintenance or repairs before operating mower. If the
mower should happen to fail despite regular mainte-
nance, please call our customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY OR MULCH
PROPERLY.
WEAR PROPER EYE PROTECTION WHILE REMOVING,
SHARPENING, AND INSTALLING BLADE. ENSURE THAT
SAFETY KEY AND BATTERIES ARE REMOVED.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand
causes the blade to dull quickly. If your lawn has sandy
soil, more frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to keep
it balanced, removing equal amounts of material from
both ends.
NOTE:
1. Be sure the mower is turned off . Remove the key and
batteries.
2. Place the mower in stand up storage mode.
TO SHARPEN BLADE IN A VISE (SEE Fig. K)
1. Be sure the bail handle is released, the blade has
stopped and the safety key and battery removed
before removing the blade.
2. Remove blade from mower. See instructions for
removing and attaching blade.
3. Secure blade K-1 in a vise K-2.
4. Wear safety glasses and be careful not to cut your-
self.
5. Carefully file the cutting edges of the blade with a
fine tooth file K-3 or sharpening stone.
6. Check balance of blade. See instructions for blade
balancing.
7. Replace blade on mower and tighten securely. Refer
to instructions below.
BLADE BALANCING (See Fig. L)
Check balance of blade by placing center hole in blade
L-1 over a screwdriver shank L-2, clamped horizontally
in a vise L-3. If either end of the blade rotates downward,
file that end. Blade is properly balanced when neither
end drops.
BLADE MAINTENANCE (See Fig. M1, M2)
Replace yourMower Blade after 50 hours mowing or 2
years, which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the
Blade. You will need garden gloves (not provided) and
a spanner wrench (not provided) to remove the Blade.
Содержание WP733E
