Worx WG650, Руководство пользователя, Страница: 12 / 36

Snow thrower en
13 12
ASSeMBLY
cautioN! inspect wiring, which,
if damaged during shipping, may
cause serious bodily injury during
equipment use. if any damage is seen
or suspected, do not assemble. instead,
contact worX customer Service
866-354-worX (9679) for assistance.
handle with care during assembly so
that electrical wiring does not become
damaged.
gEttiNg StartEd
1. Remove the Snow Thrower and all other
items from the box.
2. Determine the left and right hand sides
of the Snow Thrower by standing in the
normal operating position.
3. Check all items for shipping damage. if
damage is seen or suspected, or if any of
the parts are missing, do not assemble.
instead, promptly inform the dealer where
you bought the Snow Thrower or contact
WORX customer service for assistance.
1. iNStaLLiNg thE haNdLES
1) Loosen and remove the four sets of bolts,
washers, and Locking Cam Levers (9).
2) Attach the Middle Handle (10) with the
bolts and Locking Cam Levers to the Lower
Handle (15) (See Fig. A1).
imPortaNt: when attaching the middle
handle to the Lower handle, make sure
the chute crank bar (11) mounting
hole on the middle handle bar is facing
upwards (side of bar where hole is
indented). Later in assembly you must
make sure the chute crank bar (11) rest
on top of the middle handle bar
(See Fig. a2).
3) The bolt should be inserted through the
handles from the inside out and should
protrude from the outside hole as far as
possible. After this, place the washer on
the end of the bolt followed by the Locking
Cam Lever. Tighten the Locking Cam Lever,
flip it in to lock it, and make sure the handle
has a secure fit (See Fig. b).
The cam lever pressure can be adjusted by
turning the Locking Cam Levers clockwise
(tighten) or counter-clockwise (loosen). DO
NOT OVeR TigHTeN.
4) Connect the Upper handle(3) to the Middle
handle in the same way as described
in step 2 and 3. Use the bolts, washers,
and Locking Cam Levers to secure the
connection on both sides (See Fig. C, D, e).
5) You can use the Cable Clips (13) to keep
the cord neatly secured against the handle
bars. First, insert the cord into the Cable
Clip ensuring there is enough cord slack.
Then simply snap the clip onto the bar.
evenly space out and repeat process for
the other Cable Clips (See Fig. F).
NotE: the upper handle can be adjusted
to 3 different height positions (See Fig.
d: 1, 2, 3).
2. iNStaLLiNg thE chutE craNk
1) Lift the Chute Deflector (4) so that it snaps
and locks securely onto the Discharge chute
(6) (See Fig. g, H).
2) Raise or lower the Chute Deflector to the
desired height of the snow stream and
tighten the Chute Deflector Knobs (5)
(See Fig. i).
NotE: do not overtighten the chute
deflector knobs.
3) Locate the upper Chute Crank bar (11) in
the parts bag. Remove the screw and nut
from the upper Chute Crank bar using
a Phillips screwdriver and the wrench
provided (See Fig. J).
NotE: you may be able to unfasten the
screw and nut by hand.
4) Slide the upper Chute Crank bar into the
lower Chute Crank bar, aligning the screw
holes. Tighten the screw into the aligned
holes using a screwdriver. Fasten the nut
with a wrench (See Fig. K, L) .
5) First, loosen the screw. insert the end of the
lower Chute Crank bar into the shroud (See
fig. M1, M2).
NotE:
Make sure the flat end of the Chute
Crank bar is put into appropriate relative
position of the shroud.
Then tighten the screw. (See fig.N)
6) Remove the washer and wing nut from the
eye bolt found on the upper Chute Crank bar.
insert the eye bolt into the indented hole