Worx WG163, Руководство пользователя, Страница: 11 / 28

2 in 1: Trimmer / Edger EN
11
ASSEMBLY & OPERATION
Action Figure
ASSEMBLY
Assembling the Safety Guard See Fig. A1 & A2
Mounting the Edger Wheel See Fig. B
Installing and Removing the
Battery Pack
See Fig. C
Charging the battery pack
More details can be found in
charger’s manual
See Fig. D
Operation
Safety ON/OFF Switch See Fig. E
Trimming
- Adjusting the Shaft See Fig. F
- Adjusting the Trimmer Head See Fig. G1, G2
- Adjusting the Auxiliary handle See Fig. H
- Trimming See Fig. I1
- Using the Flower Guard See Fig. I2
Edging
- Changing the tool into the Edg-
ing mode
See Fig. J1, J2
- Edging See Fig. K
Command feeding the line See Fig. L
Manually feeding the line See Fig. M
Replacing the trimmer Spool
See Fig. N1, N2,
N3
Manually winding the line
See Fig. O1, O2,
O3, O4
OPERATION INSTRUCTIONS
WARNING!
The charger and battery pack
are specially designed to work together so
do not attempt to use any other devices. Never insert
or allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
1. Automatic line feed system
When initially switching on the trimmer, a small
length of line is fed out. Each time the tool is started
from rest it will advance about 0.25 inches of trimmer
line.
A ‘clattering’ noise will be heard when the lines hit
the Line Cutter. DO NOT BE ALARMED. This is quite
normal. After about 5 seconds the line will be cut to
the correct length and the noise will reduce as the
motor gains full speed.
If the noise of the line being cut can’t be heard, more
line will need to be fed out.
To feed more line, it is first necessary to allow the
trimmer to stop completely; it must come to a
complete rest, then restart, allowing the motor to
reach full speed.
Repeat above until you hear the line hitting against
the Line Cutter.
2.
TM
(See Fig. L)
Your trimmer is equipped with a Command Feed
System. For efficiently feeding the line, just press the
command feed button while the machine is running
until you hear the ‘clattering’ noise of the line cutting.
The motor will shut off when pressing the Command
Feed button and will restart when releasing
the button. During that process the line will
automatically feed additional line for cutting.
3. Manually feeding the line (See Fig. M)
Turn off the trimmer and remove the battery. If
required, line can be fed out manually. To operate,
press and release manual Line Feed Button, while
gently pulling out the line until it is long enough to
reach the Line Cutter. If the line extends past the Line
Cutter, too much line has been fed out. If too much
line is fed out, remove the Spool Cap and turn Spool
counter-clockwise until the line is at the desired
length.
4. Manually winding the line ( See Fig. O1, O2,
O3, O4)
Take approximately 10ft (3m) of line. Insert 5/8 inch
(15mm) of line into the Spool holes and wind line in
the direction of the arrows on the top of the Spool.
Leave approximately 4 inches (100mm) of line
unwound and place into the cleat. Ensure that the
line is neatly coiled on the Spool. Failure to do so will
impair the efficiency of the automatic line feed. Then
fit the Spool as shown in Fig. N1, N2, N3
MAINTENANCE
After use, disconnect the battery from the tool and
check for damage.
Your power tool requires no additional lubrication
or maintenance. There are no user serviceable parts
in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with a
dry cloth. Always store your power tool in a dry room
temperature location. Keep the motor ventilation
slots clean. Keep all working controls free of dust.