background image

220W 3-in-1 Multi Purpose Sander

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909

MODEL No.: S1B-DW01-220W  •  09/2018  •  61865

(toll free)

AFTER SALES SUPPORT

(toll free)

220W 3-in-1 Multi Purpose Sander

e-mail: [email protected]

1800 909 909

MODEL No.: S1B-DW01-220W  •  09/2018  •  61865

14

15

Assembly 

Preparation

It is best to make a trial run on a scrap piece of material  to determine the 

optimum grades of sandpaper for a particular job. If there are still marks 

on your work  after sanding, try either going back to a coarser grade  and 

sanding the marks out before recommencing with  the original choice of 

grit, or try using a new piece of  sandpaper to eliminate the unwanted marks 

before going  on to a finer grit and finishing the job.

Fitting / Attaching the sanding sheet

WARNING! Always remove the plug from the mains power socket 

before carrying out any work on the sander.

NOTE: Before fitting a new sanding sheet, remove any dust and dirt from the 

sander plate.

Attaching sanding sheets using Velcro:

NOTE: Make sure the holes on the sandpaper are aligned with the holes on 

the sander base plate.  This ensures maximum dust removal and allows air 

flow from the motor.
1.   Attach the sanding sheet to the fitted sander 

plate by simply applying the underside of the 

sandpaper onto the velcro base (Fig J).  This 

type of sandpaper is “hook and loop”, and the 

velcro holds the sanding sheet in place.

2.   To remove the sanding sheet, simply pull the 

sanding sheet off the sander plate (Fig K).

Preparation

Fitting/changing the sander plates –  

Random Orbital Sander Plate

WARNING! Always remove the plug from the mains power socket 

before carrying out any work on the sander.

Changing from the fitted rectangle sander plate (9) to the Random Orbital 

Sander plate (13).
1.    Using a philips head screwdriver (not supplied), 

remove the four screws (12) visible on the 

underside of the rectangle sander plate (9)  

in an anti-clockwise direction (Fig A).

2.   Once the 4 screws are all loose, remove the  

pre-fitted rectangle sander plate (9) (Fig B).

3.   The random orbital sander plate (13) only 

requires fixing of the 4 x screws, and does not 

require the rubber pins to be used.

4.   Align the screw holes on the random orbital 

sander plate (13) underside (non Velcro side), 

with the threaded holes on the sander drive  

plate (Fig H).

5.   Using 4 x screw + washers from either of the 

other sander plates (9) / (11), secure the random 

orbital sander plate (13) onto the sander drive 

plate by screwing in a clockwise direction (Fig I).

K.

J

H.

I.

TIGHTEN

Selecting the suitable sanding sheet

The material removal rate and surface quality are determined by the grain 

strength of the sandpaper.  Ensure you use a suitable grit (g) of sandpaper 

for working on different materials.  The 80 grit (g) sandpaper supplied is 

used for more coarse / rougher sanding / removal.  The 240 grit (g) is better 

suited for detail and fine sanding.  This sander includes an 80g and 240g 

sandpaper sheet for each sander plate base.

Содержание 61865
















Отзывы: