background image

4

5

3730 E. SOUTHERN AVE., PHOENIX, AZ 85040 | USA

800.778.8779 | WORKHORSEPRODUCTS.COM

SPECIFICATIONS

SAFETY INFORMATION

WARNING!

RISK OF ELECTRICAL SHOCK! Turn ALL power to the unit OFF before service.

All service should be done by or under the supervision of a trained technician.

THIS ELECTRIC DRYER IS INTENDED SOLELY FOR THE PURPOSE OF CURING INK ON 

TEXTILE AND CUT GOODS. THIS DRYER IS NOT INTENDED FOR USE IN HEATING, 

CURING OR BAKING OF ANY OTHER MATERIALS. THIS DRYER IS INTENDED FOR 

INDOOR USE ONLY.

THE EXCLAMATION WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE 

USER OF IMPORTANT SAFETY PRECAUTIONS SHOP PERSONNEL SHOULD BE AWARE 

OF DURING OPERATION.

For your safety, do not store or use gasoline or other flammable vapors and liquids in the vicinity 

(at least 3’ (1 Meter)) of this or any other appliance.

Vent lines to the outdoors must be installed by a qualified HVAC engineer on all air exhaust 

components equipped with a vent fitting.

Proper grounding (a ground rod at the equipment footing), according to NEC requirements, must 

be provided for during electrical connection by a QUALIFIED ELECTRICIAN.

Never alter the internal wiring of this machine.

Never place any item other than the substrates to be cured or dried on this dryer’s conveyor belt. 

Do not overload the belt.

Do not let the conveyor belt track off the conveyor drive rollers.

Keep all loose articles (including clothing, hair, jewelry, etc.) away from the conveyor belt.

Never leave the machine unattended during operation.

Do not perform maintenance on this machine until all power has been shut off at the dryer AND at 

the incoming power circuit breaker.

Part Number

Belt Size

Production Capacity

Power Requirements

Infeed/Exit x Chamber

Part Number

Belt Size

Production Capacity

Power Requirements

Infeed/Exit x Chamber

PD5409-3-3P

54” x 9’

(137cm x 275cm)

900+/HR - 

Plastisol

300-400/HR - 

Waterbased

ELECTRIC

3-Phase: 240V, 50-60Hz, 

22,217W, 58A

26” x 54”

(66cm x 137cm) 

PD5409-4-3P

54” x 9’

(137cm x 275cm)

950+/HR - 

Plastisol

300-400/HR - 

Waterbased

ELECTRIC

3-Phase: 240V, 50-60Hz, 

29,417W, 76A

26” x 54”

(66cm x 137cm) 

PD3009-3-1P (3P)

30” x 9’

(76cm x 275cm)

400-500/HR - 

Plastisol

100-200/HR - 

Waterbased

ELECTRIC

1-Phase: 240V, 50-60Hz, 

11,309W, 47A

OPTIONAL

3-Phase: 240V, 50-60Hz, 

11,417W, 31A

26” x 54”

(66cm x 137cm) 

PD3009-4-1P (3P)

30” x 9’

(76cm x 275cm)

900+/HR - 

Plastisol

300-400/HR - 

Waterbased

ELECTRIC

1-Phase: 240V, 50-60Hz, 

14,909W, 62A

OPTIONAL

3-Phase: 240V, 50-60Hz, 

15,017W, 40A

26” x 54”

(66cm x 137cm) 

Содержание PD3009-3-1P


















Отзывы: