Work Pro WAP 505, Руководство пользователя

Страница: 7 / 10

CAUTION
CAUTION
After to use it, please make sure to switch off the main power to avoid battery damages.
Take the battery out if you are not going to use it for a period of time.
2. This unit incorporates low voltage circuit protection for the built-in battery to avoid damages in case of incorrect
operation. When the main receiver is being used, if the voltage of the battery is less than 9 +/- 0.5 V, it will switch
off its power automatically by its low voltage circuit protection and need to be used with AC power in order to
recharge the battery.
CAUTION
CAUTION
Be sure to switch off the system main power after use, otherwise the battery will be over discharged
and it can damage the rechargeable battery, shorting the battery life.
If the LED flash up, it shows the battery is good to use. If LED is on, it shows the battery is low, you
have to change the battery before to use the system. If the LED does not flash and not on, the battery
is empty or polarity is wrong.
OPERATION WITH LAVALIER MICROPHONE
1. Open the battery compartment by sliding up the cover.
2. Put the battery into the compartment with correct polarity and close the cover.
3. Plug the Lavalier microphone jack on the transmitter.
4. Switch on the power of the transmitter and when the LED lits, it is ready to work.
5. Be careful to adjust the main control of the transmitter, start from least volume and slowly turn it to an
appropriate level to hear your voice clearly.
6. After use, you have to take the battery out of the transmitter to avoid battery leaking to damage the transmitter.
OPERATION WITH HANDHELD MICROPHONE
1. Open the battery cover.
2. Put the battery into the compartment and make sure you have a right polarity before you use it.
3. Turn the switch to ON , now you can use the microphone.
Cover
Cover
Volume
Power LED
Power Switch
MIC port
9V battery
chamber
Page 5 User Manual WAP 505
EN
FUNCIONAMIENTO DEL SISTEMA
FUNCIONAMIENTO CON ALIMENTACION AC
1. Conecte el cable AC a la toma mural. Asegúrese de utilizar el voltaje correcto con la unidad.
2. Pulse el interruptor de encendido a ON, el LED seiluminará. Después de utilizar la unidad, asegúrese de
pulsar el interruptor a OFF para evitar sobrecargar la batería.
3. Cuando la alimentación AC se corta de súbito, la batería incorporada se encarga de alimentar el sistema
sin tiempo de retardo entre ambos cambios.
FUNCIONAMIENTO CON ALIMENTACION DC
1. Pulse el interruptor a ON, el LED power le indicará que la batería funciona adecuadamente. La intensidad del
LED disminuirá de acuerdo al tiempo de uso.
PRECAUCION
PRECAUCION
PRECAUCION
PRECAUCION
Debe desconectar el sistema de la alimentación si no va a usar la unidad durante un tiempo.
Antes de poner en marcha la unidad, la batería debe ser cargada al menos durante 8 horas.
Asegúrese de apagar la alimentación después de su uso, si no la batería se descargará, dañándola
y acortando su vida útil.
Si mientras funciona la unidad se producen interrupciones ruidosas o distorsiones, indica un bajo
nivel de carga en la batería, debe cambiar a alimentación AC y recargarla.
Página 13
Manual de Instrucciones WAP 505
Botón MODE
Selector USB/SD
Botón STOP
LED MODE
Puerto SD/MMC
Puerto USB
LED Play/Pause
Botón Play/pause
Botón Backward
Botón Forward
Volumen USB/SD
Volumen ECHO
Volumen Tono
Volumen AUX
Volumen MIC c/cable
Volumen MIC inalamb.
LED RF
LED cargador DC 8.4V
LED cargador DC 12V
Micro c/cable 1,2,3
LED power
Interruptor red/carga
Entrada alimentación AC
Entrada aliment. DC 12 V 1A
Entrada aliment. DC 12 V 1A
Alojamiento para carga pila 8.4 V DC
Alojamiento para carga batería 12 V DC
Tapa
Altavoz
Audio OUT
AUX IN (MP3/CD)
Salida altavoz externo 4 ohm
ES