manualshive.com logo in svg

Worcester greenstar heatslave 18, Инструкция по эксплуатации

Поделиться
Скачать
Worcester greenstar heatslave 18 Скачать руководство пользователя страница 39

S

E

R

VICI

NG

& S

PA

R

E

S

INSTALLATION & SERVICING INSTRUCTIONS FOR WORCESTER BOSCH

37

INSPECTION AND SERVICE

8-716-106-252a (03.05)

INSPECTION AND SERVICE

External oil filter:

 Remove the paper element from the external oil

filter and replace it. If the filter contains a washable

element, thoroughly clean in kerosene and

reassemble into the filter.

Clean the boiler:

Manifold access:

 Release screws (E) to remove the flue manifold

access cover (F) and clear any debris.

 Check the condensate route (G) is clear and

clean the condensate trap and pipework.

 Check and clean the flue system if necessary.
 Remove the baffle retainer (J) and baffles (H)

from the secondary heat exchanger.

 Check and clean the secondary heat exchanger

surfaces.

 Pour 500ml of water into drain (G) to refill the

condensate trap.

 Clean the secondary heat exchanger baffles

(H) if necessary and refit correctly.

 Refit the baffle retainer (J).
 Check the seal on the manifold access cover

(F) and replace if necessary.

 Replace the flue manifold access cover (F)

and secure with screws (E).

Combustion chamber:

 Release the M10 retaining nuts and washers

(B) and remove combustion chamber access

door (A).

 Check the fibreglass rope seal on the

combustion chamber access door (A) and

replace if necessary.

 Remove and check the baffle retainer (D).
 Remove the baffles (C), clean and check the

condition of the baffles and the acoustic

insulation. Replace any baffles or insulation pads

considered to be badly corroded/degraded.

 Thoroughly clean all of the heat exchanger

surfaces using a suitable brush and clear all

loose debris from the combustion chamber.

 Check the condition of the combustion

chamber access door insulation. If the insulation

is damaged the door assembly must be replaced.

 Refit the items in reverse order ensure the

baffles (C) and baffle retainers (D) are correctly

fitted for the boiler output as shown in the plan

view opposite.

 Refit combustion chamber cover (A).
 Secure with nuts and washers (B) and tighten

until the door is firmly secured, do not over

tighten the nuts.

Fire valve:

 Check that the oil supply pipe has a fire valve

fitted externally to the building with a fire detection

element located within the appliance case. A

fire valve clip (K) is provided for this purpose.

A

B

D

C

K

E

F

H

G

J

Plan sectional view

18/25kW

Содержание greenstar heatslave 18

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды