Worcester GREENSTAR 30CDi Classic System ErP 41-406-37 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 60

Worcester GREENSTAR 30CDi Classic System ErP 41-406-37 Скачать руководство пользователя страница 9

PRE-INSTALLATION

6 720 812 175 (2014/07)

9

3

PRE-INSTALLATION

3.1

CLEANING PRIMARY SYSTEMS

BEFORE CLEANING THE SYSTEM:

▶

Ensure that the system and pipe work is in good working order.

▶

Where possible keep the existing boiler/circulating pump in place
when flushing the system.

FOLLOW THE GUIDANCE OF BS7593:

Treatment of water in domestic hot water central heating and also the
flushing guidelines below.

FLUSHING THE SYSTEM

▶ Fill the system with cold water and check for leaks.
▶ Open all drain cocks and drain the system.
▶ Close drain cocks and add a suitable flushing agent

compatible with

aluminium

at the correct strength for the system conditions in

accordance with the manufacturer‘s instructions.

The pH value of the system water must be less than 8 or the
appliance guarantee will be invalidated.

▶ Circulate the flushing agent before the boiler is fired up.
▶ Run the boiler/system at normal operating temperature as directed by

the manufacturer of the flushing agent.

▶ Drain and thoroughly flush the system to remove the flushing agent

and debris.

▶ It may be necessary to use a power flushing machine to aid the

cleansing procedure in some circumstances.

▶ Close the drain cocks and refill with fresh water and a suitable

inhibitor.

▶ Vent any air from the boiler and system.

INHIBITOR

Add a suitable inhibitor or combined inhibitor/anti-freeze, if the system
is exposed to freezing conditions, to the heating system in accordance
with the DWTA code of practice and manufacturer‘s guidelines.

WATER TREATMENT PRODUCTS

Suitable water treatment products can be obtain from the following
manufacturers:

3.2

MAINS SUPPLY

3.2.1

GAS SUPPLY

• Boilers using Natural Gas (NG) must be connected to a governed

meter.

• Liquid Petroleum Gas (LPG) must be connected to a regulator.
• Installation and connection of the gas supply to the boiler must be in

accordance with BS6891.

• Under no circumstance should be size of the gas supply pipe be less

than 22 mm.

• The meter or regulator and pipe work to the meter must be checked,

preferably by the gas supplier. This is to ensure that the equipment is
in good working order and can meet the gas flow and pressure
requirements, in addition to the demand from any other appliance
being served.

CAUTION:

MAINS SUPPLIES

▶ Isolate the mains supplies before starting any work

and observe all relevant safety precautions.

NOTICE:

Before installation

▶ All the following Pre-Installation sections must be read

and requirements met before starting boiler or flue
installations.

NOTICE:

Water treatment

▶ Debris from the system can damage the boiler and

reduce efficiency. Failure to comply with the
guidelines for the use of water treatment with the
appliance will invalidate the appliance warranty.

NOTICE:

ARTIFICIALLY SOFTENED WATER MUST NOT

BE USED TO FILL THE CENTRAL HEATING SYSTEM.

WARNING:

Sealing agents

▶ The addition of sealing agents to the system water is

not permitted as this can cause problems with
deposits left in the heat exchanger.

FERNOX

0870 601 5000

www.fernox.com

SENTINEL

0800 389 4670

www.sentinel-solutions.net

Table 9

«
...
7
8
9
10
11
...
»

Содержание GREENSTAR 30CDi Classic System ErP 41-406-37





























































Отзывы:

Нет отзывов