Worcester GREENSTAR 30CDi Classic System ErP 41-406-37 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 60

Worcester GREENSTAR 30CDi Classic System ErP 41-406-37 Скачать руководство пользователя страница 46

SERVICING AND SPARES

6 720 812 175 (2014/07)

46

Fig. 86 Heat exchanger removal 3

4. Undo flue connection (E) from sump (F).

▶ Pull flue pipe up.
▶ Remove the heat exchanger.

Fig. 87 Heat exchanger removal 4

17. DIVERTER VALVE MOTOR (IF FITTED)

There is no need to drain the appliance.

▶ Disconnect the electrical connector from the diverter valve motor.

1. Pull the motor assembly (A) towards you.

The assembly will slide free from the valve.

▶ To refit, follow the above in reverse.

Fig. 88 Diverter valve motor removal

18. DIVERTER VALVE

▶ Ensure the appliance has been fully drained.
▶ Disconnect the electrical connector from the diverter valve motor.
▶ Undo the two screws holding the valve to the plastic housing.

Fig. 89 Diverter valve removal

1. Withdraw the valve (B) and clean the valve chamber if necessary.

▶ To refit, follow the above in reverse.

Ensure any seals that have been disturbed are renewed.

19. AUTO AIR VENT

▶ Ensure the appliance has been fully drained.

1. Use a screwdriver or similar to rotate the air vent anticlockwise.
2. Lift the air vent (C) out of the housing and remove.

▶ To refit, follow the above in reverse.

Fig. 90 Auto Air Vent removal

In case of problems when refitting the motor: Connect
the electrical connector to the motor and switch the
appliance on. Then the motor goes to the middle position
and you can refit it without difficulty.

8.

C

D

3.

6 720 812 175-19.1O

4.

E

F

6720647361-70.1Wo

1.

A

6720647361-40.1Wo

1.

B

6720647361-50.1Wo

C

2.

1.

6 720 812 175-21.1O

N

«
...
44
45
46
47
48
...
»

Содержание GREENSTAR 30CDi Classic System ErP 41-406-37





























































Отзывы:

Нет отзывов