Worcester GREENSTAR 30CDi Classic System ErP 41-406-37 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 60

Worcester GREENSTAR 30CDi Classic System ErP 41-406-37 Скачать руководство пользователя страница 35

COMMISSIONING

6 720 812 175 (2014/07)

35

5.7

FINISHING COMMISSIONING

The boiler has been factory set, so there should be no need to adjust
combustion settings.

REPLACE OUTER CASING:

1. Replace outer casing making sure that the securing points are

properly located.

▶ Press the clip (A) downwards to secure casing on top.
▶ Retighten bottom two screws (B).

INSTALLING BOTTOM PANEL:

2. The bottom panel slides onto two ledges (C) either side of the boiler

frame.

▶ Hold the panel up against the underside of the boiler and slide

towards the rear until it is fully engaged.

HANDOVER:

▶ Complete the Benchmark check list.
▶ The fascia cover is opened by pulling the flap (D) towards you.
▶ Set up the controls and show the user how to operate all the controls

shown in the User Guide.

▶ Place the user guide into the tray (E) on the inside of the facia cover.
▶ If the appliance is unused and exposed to freezing conditions; shut off

all the mains supplies and drain the system and boiler.

Fig. 53 Fitting outer case

Fig. 54 Fitting bottom panel

B

B

A

6720647361-25.3Wo

C

D

6720647361-26.3Wo

«
...
33
34
35
36
37
...
»

Содержание GREENSTAR 30CDi Classic System ErP 41-406-37





























































Отзывы:

Нет отзывов