background image

 2 

 

 

 

Before you start the installation of your kit, please read the following: 

 

This kit is intended to be fitted by someone who is competent and experienced at fitting electric kits to 
bikes. If you are not experienced and/or lack the necessary tools to complete any of the procedures in 
this manual, you should seek the advice of a professional who can fit the kit for you. If necessary, call us 
on 

01702 684444 

or email us at 

[email protected] 

and we will try and put you in touch with 

someone in your area that has the necessary expertise to properly fit your kit. You will of course need to 
pay for the technician to install your kit, these costs are not covered by Woosh Bikes. 

 

There are several different types of pedelec sensor, we would normally have determined which type is 
suitable for your bike before you finalised your order. If we didn’t, please contact us before attempting 
to fit your kit. 

 

Warranty Terms: 

If your kit is fitted by a professional installer, it will be covered by our standard one year warranty, which 
means that in the event of a failure, you would first need to have the person that installed your kit con-
firm the issue and likely cause, then you (or the installer) would need to contact us and provide us with 
the details of the fault. If the issue cannot be resolved over the phone or via email, then you would need 
to return the faulty part to us at your expense. We will then repair or replace the faulty part and send it 
back to you at our expense. If the kit was not fitted by a professional and/or the failure that has occurred 
is due to poor/incorrect installation, or the kit has been used improperly, the warranty will be voided.

 

Содержание Hub Kit


















Отзывы: