manualshive.com logo in svg

Woodward SPM-D11, Руководство пользователя

Поделиться
Скачать
Woodward SPM-D11 Скачать руководство пользователя страница 59

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 59/79 

 

Phase matching 
Gain          00 

Zero phase control = ON 

Phase matching control gain 

1 to 36 

This configuration screen only appears, if the phase matching control is configured 
ON! 
When phase matching control is enabled, this gain determines how much the output 
signal is changed depending on phase difference. By increasing the gain, the re-
sponse is increased to permit larger corrections to the variable to be controlled re-
sulting in longer ON time periods. The farther out of tolerance the process is the 
larger the response action is to return the process to the tolerance band. If the gain 
is configured too high, the result is excessive overshoot/undershoot of the desired 
value.  
Prior to setting the value for this gain, the frequency controller must be enabled and 
properly adjusted. 

 

Phase matching 
df start  0.00Hz 

Zero phase control = ON 

Differential frequency for starting phase matching control 

0.02 to 0.25 Hz 

This configuration screen only appears, if the phase matching control is configured 
ON! 
The phase matching control is not enabled, until the differential frequency between 
generator and busbar/ mains is lower than the value configured here. 

Synchronization Time Monitoring 

Sync.time contr. 
Alarm       ON 

Synchronization time monitoring 

ON/OFF 

ON

................ This setting ensures that the synchronization time is monitored. A 

timer is started when synchronization is initiated. If the circuit 
breaker has not closed prior the timer expiring, the warning message 
"Synchronization time" is displayed. In addition, the synchronization 
procedure is cancelled and the "Ready for operation" relay is de-
energized. By pressing the "Clear" button for at least 3 seconds or by 
removing one of the conditions which are necessary for the synchro-
nization (e.g. terminal 3 "Release CB"), the synchronization timer is 
reset. The following screens of this function are displayed. 

OFF

.............. The synchronization time will not be monitored. The following 

screens of this function are not displayed. 

 

Sync.time contr. 
Delay time 000s 

Final value for synchronization time monitoring 

10 to 999 s 

Please refer to the above description of the configuration screen. 

 

Содержание SPM-D11
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды