Woodward HighPROTEC Скачать руководство пользователя страница 19

Страница: 19 / 22

Problem or maloperation in…

Problem Description

Corrective Action

Is Smart view access via ProtCom enabled on the
device? Check the <Device Para/ Security/
Communication> settings.

Line Differential: Protection Communication not
working.

Protection Communication not working.
State <Operation/ Status Display/ Prot-Transfer/
ProtCom/ State/ Comm. Ok> is 0.

Check <Operation/ Status Display/ Prot-Transfer/
ProtCom/ State/ Communication>:

•

Err (no RX) or Err (no TX)

•

check wiring

•

verify that fiber optic line is connected to
the correct fiber optic port

•

Err (corrupt data)
device is connected to a non-HighPROTEC device

•

Err (incomp. IDs)

•

connected to wrong partner device

•

or adjust <Protection Para/ Global Prot
Para/ Prot-Transfer/ ProtCom/ Pair ID>

•

Err (incomp. frequ)
devices are configured to different nominal
frequencies

•

Err (incomp version)
devices contain different firmware version, please
update the firmware

•

Err (incomp. Sync 1) or Err (incomp. Sync 2)
check fiber optic:

•

Fiber optic not plugged in correctly

HighPROTEC Troubleshooting Guide DOK-HB-TSE Rev. B

Содержание HighPROTEC























Результаты поиска

Содержание HighPROTEC

Отзывы:

Похожие инструкции для HighPROTEC

Бренды по названию

Популярные бренды

Woodward HighPROTEC, Руководство по устранению неисправностей

Результаты поиска

Содержание HighPROTEC

Отзывы:

Похожие инструкции для HighPROTEC

Бренды по названию

Популярные бренды