background image

 

WARNING 

Read this entire manual and all other publications pertaining to the work to be 

performed before installing, operating, or servicing this equipment. Practice all 

plant and safety instructions and precautions. Failure to follow instructions can 

cause personal injury and/or property damage. 

 

The engine, turbine, or other type of prime mover should be equipped with an 

overspeed shutdown device to protect against runaway or damage to the prime 

mover with possible personal injury, loss of life, or property damage. 

 

The overspeed shutdown device must be totally independent of the prime mover 

control system. An overtemperature or overpressure shutdown device may also be 

needed for safety, as appropriate. 

 

 

 

CAUTION 

To prevent damage to a control system that uses an alternator or battery-charging 

device, make sure the charging device is turned off before disconnecting the 

battery from the system. 

 

In systems where large inductive loads are switched on the DC power buss, surge 

impulse energy will be present due to the switching. To address surge energy 

affects on the control, appropriate suppression devices must be installed in the DC 

power buss prior to the control’s power connection. 

 

Electronic controls contain static-sensitive parts. Observe the following 

precautions to prevent damage to these parts. 

• 

Discharge body static before handling the control (with power to the control 

turned off, contact a grounded surface and maintain contact while handling the 

control). 

• 

Avoid all plastic, vinyl, and Styrofoam (except antistatic versions) around 

printed circuit boards. 

• 

Do not touch the components or conductors on a printed circuit board with 

your hands or with conductive devices. 

 

 

 

 

 

 

 

 

IMPORTANT DEFINITIONS 

WARNING—indicates a potentially hazardous situation which, if not avoided, could 

result in death or serious injury. 

 

CAUTION—indicates a potentially hazardous situation which, if not avoided, could 

result in damage to equipment. 

 

NOTE—provides other helpful information that does not fall under the warning or 

caution categories.

 

 

 

Revisions—Text changes are indicated by a black line alongside the text. 

 

 

 

 

 

Woodward Governor Company reserves the right to update any portion of this publication at any 

time. Information provided by Woodward Governor Company is believed to be correct and 

reliable. However, no responsibility is assumed by Woodward Governor Company unless 

otherwise expressly undertaken. 

© Woodward 2005 

All Rights Reserved 

Содержание DPG-2201-00 Series



















































Отзывы: