manualshive.com logo in svg

Woodward 721, Руководство по эксплуатации и калибровке

Поделиться
Скачать
Woodward 721 Скачать руководство пользователя страница 32

721DSC for Marine Propulsion Application 

 

Manual 26004

 

Woodward

  

28

 

7. 

Torque Lmt P3, % 

 

Torque Lmt P3, % is the maximum actuator output current in percent at the third 
torque limit. 

 

8. 

Torque Lmt P4, rpm 

 

Torque Lmt P4, rpm is the engine speed in RPM at the fourth torque limit. 

 

9. 

Torque Lmt P4, % 

 

Torque Lmt P4, % is the maximum actuator output current in percent at the fourth 

torque limit. 

 

10.  Maximum Fuel Limit 

 

Maximum Fuel Limit sets the maximum actuator output current. If 100% is set at this 

set point, the maximum actuator output current is 180 mA. Set this set point to a value 
a little above the actuator output value for full load. 

 

 

Display 2 

These are menus to monitor input/output status. 

 

1. 

Speed Signal #1 

 

Speed Signal #1 displays the speed signal input to speed signal input channel #1. 

 

2. 

Speed Signal #2 

 

Speed Signal #2 displays the speed signal input to speed signal input channel #2. 

 

3. 

KW Signal Input,% 

 

KW Signal Input,% displays the input signal from the KW transducer in percent. 

 

4. 

Spd Set Input,mA 

 

Spd Set Input,mA displays the external remote speed setting input signal in mA. 

 

5. Contact 

A 

Status 

 

Contact A Status displays the status of the RUN/STOP contact (open or closed). 

 

6. Contact 

B 

Status 

 

Contact B Status displays the status of the IDLE SPEED/START SPEED contact (open 

or closed). 

 

7. 

Contact C Status 

 

Contact C Status displays the status of the RAISE SPEED contact (open or closed). 

 

8. 

Contact D Status 

 

Contact D Status displays the status of the LOWER SPEED contact (open or closed). 

 

9. Contact 

E 

Status 

 

Contact E Status displays the status of the Generator Circuit Breaker Aux. (GCB AUX) 

contact (open or closed). 

Содержание 721





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды