manualshive.com logo in svg

Woodward 721, Руководство по эксплуатации и калибровке

Поделиться
Скачать
Woodward 721 Скачать руководство пользователя страница 28

721DSC for Marine Propulsion Application 

 

Manual 26004

 

Woodward

  

24

 

4. 

Derivative Ratio 1 

 

Derivative Ratio compensates for the actuator time constant. Set this set point to 5 for 
ordinary applications. 

 

5. 

Window Width 1 

 

Window Width is the magnitude (in rpm) of a speed error at which the control 

automatically switches to fast response. The control does not use the absolute value of 

speed error, but “anticipated” speed error to make this switch. This method provides for 
quick switching to the high gain value when an offspeed occurs and early switching to 

the low gain value when recovering from the speed transient. This provides smoother 
switching than if the absolute speed error was used for the window. 

 

6. 

Gain Ratio 1 

 

Gain Ratio is the ratio of the Gain setting at steady state to the Gain setting during 
transient conditions. The Gain Ratio operates in conjunction with the Window Width 

and Gain adjustments by multiplying the Gain set point by the Gain Ratio when the 
speed error is greater than the Window Width. This makes the control dynamics fast 
enough to minimize engine

-

speed overshoot on start

-

up and to reduce the magnitude of 

speed error when loads are changing. This allows a lower gain at steady state for better 
stability and reduced steady

-

state actuator linkage movement. 

 

7. 

Gain Breakpoint 1 

 

Gain Breakpoint sets the percent output above which the Gain Slope becomes effective. 

It should usually be set just above the minimum load output. See figure 4. The Gain 

Breakpoint adjustment is common to both sets of dynamics. 

 

8. 

Gain Slope 1 

 

Gain Slope changes Gain as a function of actuator output. Since actuator output is 
proportional to engine load, this makes gain a function of engine load. Gain slope 

operates in conjunction with the Gain Breakpoint adjustment to increase (or decrease) 
gain when percent actuator output is greater than the breakpoint. This compensates for 

systems with high (or low) gain at low load levels. This allows the gain settings to be 

lower at light or no load for engine stability, yet provide good control performance under 
loaded conditions. 

 

9. Speed 

Filter 

 

Set this value to the cutoff frequency found by using the formula below (see figure 5). 
This is the roll

-

off frequency for the firing torsional filter. The formula to get the proper 

roll

-

off frequency setting is: 

camshaft frequency  

= (engine rpm)/60 [for 2

-

cycle engines] 

 

= (engine rpm)/120 [for 4

-

cycle engines] 

firing frequency 

= 

(camshaft frequenc

y) 

×

 (number of cylinders) 

Initially set the filter frequency to the firing frequency. 

 

Содержание 721





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды