manualshive.com logo in svg

Woodward 721, Руководство по эксплуатации и калибровке

Поделиться
Скачать
Woodward 721 Скачать руководство пользователя страница 2

 

 

 

 

WARNING—DANGER OF DEATH OR PERSONAL INJURY

 

 

WARNING—FOLLOW INSTRUCTIONS 

Read this entire manual and all other publications pertaining to the work to be performed before 
installing, operating, or servicing this equipment. Practice all plant and safety instructions and 
precautions. Failure to follow instructions can cause personal injury and/or property damage. 

 

WARNING—OUT-OF-DATE PUBLICATION 

This publication may have been revised or updated since this copy was produced. To verify that 
you have the latest revision, be sure to check the Woodward website: 

www.woodward.com/pubs/current.pdf 

The revision level is shown at the bottom of the front cover after the publication number. The 
latest version of most publications is available at: 

www.woodward.com/publications 

If your publication is not there, please contact your customer service representative to get the 
latest copy. 

 

WARNING—OVERSPEED PROTECTION 

The engine, turbine, or other type of prime mover should be equipped with an overspeed 
shutdown device to protect against runaway or damage to the prime mover with possible 
personal injury, loss of life, or property damage. 

 

The overspeed shutdown device must be totally independent of the prime mover control 
system. An overtemperature or overpressure shutdown device may also be needed for safety, 
as appropriate. 

 

WARNING—PROPER USE 

Any unauthorized modifications to or use of this equipment outside its specified mechanical, 
electrical, or other operating limits may cause personal injury and/or property damage, 
including damage to the equipment. Any such unauthorized modifications: (i) constitute 
"misuse" and/or "negligence" within the meaning of the product warranty thereby excluding 
warranty coverage for any resulting damage, and (ii) invalidate product certifications or 
listings. 

 

 

CAUTION—POSSIBLE DAMAGE TO EQUIPMENT OR PROPERTY 

 

CAUTION—BATTERY CHARGING 

To prevent damage to a control system that uses an alternator or battery-charging device, make 
sure the charging device is turned off before disconnecting the battery from the system. 

 

CAUTION—ELECTROSTATIC DISCHARGE 

Electronic controls contain static-sensitive parts. Observe the following precautions to prevent 
damage to these parts. 

• 

Discharge body static before handling the control (with power to the control turned off, 
contact a grounded surface and maintain contact while handling the control). 

• 

Avoid all plastic, vinyl, and Styrofoam (except antistatic versions) around printed circuit 
boards. 

• 

Do not touch the components or conductors on a printed circuit board with your hands or 
with conductive devices. 

 

IMPORTANT DEFINITIONS 

• 

A 

WARNING

 indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury. 

• 

A 

CAUTION

 indicates a potentially hazardous situation which, if not avoided, could result in damage 

to equipment or property. 

• 

A 

NOTE

 provides other helpful information that does not fall under the warning or caution 

categories. 

 

Revisions—Text changes are indicated by a black line alongside the text. 

 
 
 
 

Woodward Governor Company reserves the right to update any portion of this publication at any time. Information provided by Woodward Governor Company is 
believed to be correct and reliable. However, no responsibility is assumed by Woodward Governor Company unless otherwise expressly undertaken. 

©

 1998 by Woodward Governor Company 

All Rights Reserved

 

 

Содержание 721





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды