Woodward 721 Скачать руководство пользователя страница 20

Страница: 20 / 52

721DSC for Marine Propulsion Application

Manual 26004

Woodward

Hand Held Programmer Keys

The programmer keys do the following functions (see Figure 5

1):

(left arrow)

Moves backward through Configure or Service, one menu at a time.

(right arrow)

Advances through Configure or Service, one menu at a time.

(up/down arrow)

Toggles between the two displayed items.

(up arrow)

Moves backward through each menu, one step at a time.

(down arrow)

Advances through each menu, one step at a time. Selects Service from

Master Screen.

(turtle up)

Increases the displayed set point value slowly.

(turtle down)

Decreases the displayed set point value slowly.

(rabbit up)

Increases the displayed set point value quickly (about 10 times faster
than the turtle keys).

(rabbit down)

Decreases the displayed set point value quickly (about 10 times faster
than the turtle keys).

– (minus)

Increases set point values by one step at a time.

+ (plus)

Decreases set point values by one step at a time.

(solid square)

Not used.

Displays the 721 control part number and software revision level.

ESC

To return to menu header or to main screen.

SAVE

Saves entered values (set points).

BKSP

Scrolls left through line of display.

SPACE

Scrolls right through line of display.

ENTER

Used when entering exact values and accessing Configure.

= (equals)

For entering exact values (within 10%).

(decimal)

To select Configure.

Содержание 721





















































Результаты поиска

Содержание 721

Отзывы:

Бренды по названию

Популярные бренды

Woodward 721, Руководство по эксплуатации и калибровке

Результаты поиска

Содержание 721

Отзывы:

Бренды по названию

Популярные бренды