Woodstock W1866 Скачать руководство пользователя страница 5

Страница: 5 / 60

-3-

Model W1866 (For Machines Mfd. Since 11/18)

DU
CT

Model W1866 Machine Specifications, Page 1 of 3

MODEL W1866

24" X 36" BOWL TURNING LATHE

Product Dimensions

Weight.......................................................................................................... 723 lbs.

Width (side‐to‐side) x Depth (front‐to‐back) x Height................................... 74‐1/4 x 37 x 58 in.

Footprint (Length x Width)......................................................................... 55 x 25‐1/2 in.

Shipping Dimensions

Type.................................................................................. Cardboard Box on Wood Skids

Content........................................................................................................ Machine

Weight.......................................................................................................... 797 lbs.

Length x Width x Height........................................................................... 58 x 31 x 30 in.

Must Ship Upright.................................................................................................. Yes

Electrical

Power Requirement.................................................................... 220V, Single‐Phase, 60 Hz

Full‐Load Current Rating....................................................................................... 15.8A

Minimum Circuit Size............................................................................................. 20A

Connection Type......................................................................................... Cord & Plug

Power Cord Included.............................................................................................. Yes

Power Cord Length............................................................................................... 6 ft.

Power Cord Gauge............................................................................................ 14 AWG

Plug Included....................................................................................................... Yes

Included Plug Type............................................................................................... 6‐20

Inverter (VFD) Type............................................................................. Delta VFD022E21A

Inverter (VFD) Size............................................................................................... 3 HP

Motors

Main

Horsepower................................................................................................. 3 HP

Phase.................................................................................................... 3‐Phase

Amps.......................................................................................................... 8.5

Speed........................................................................................................ 1720

Type............................................................................................ TEFC Induction

Power Transfer ..................................................................................... Belt Drive

Bearings................................................................. Sealed & Permanently Lubricated

Содержание W1866





























































Результаты поиска

Содержание W1866

Отзывы:

Похожие инструкции для W1866

Бренды по названию

Популярные бренды

Woodstock W1866, Руководство пользователя

Результаты поиска

Содержание W1866

Отзывы:

Похожие инструкции для W1866

Бренды по названию

Популярные бренды