Woodstock W1866 Скачать руководство пользователя страница 25

Страница: 25 / 60

-23-

Model W1866 (For Machines Mfd. Since 11/18)

The test run consists of verifying the following: 1) The

motor powers up and runs correctly, and 2) the safety

disabling mechanism on the switch works correctly.

To.test.run.the.machine,.do.these.steps:

1. Clear all setup tools away from machine.

2. Ensure spindle lock is turned left to the unlocked

position.

3. Set spindle direction switch to OFF position,

and rotate speed-control knob all the way

counterclockwise.

4. Press Emergency Stop button (see Figure

5. Connect machine to power supply. Digital readout

should illuminate.

6. Twist Emergency Stop button clockwise until it

springs out. This resets switch so spindle can turn.

7. Press blue RESET button.

8. Verify machine is operating correctly by turning

spindle direction switch to "F" position, then slowly

rotate speed-control knob clockwise.

— When operating correctly, machine runs smoothly

with little or no vibration or rubbing noises.

— Investigate and correct strange or unusual noises

or vibrations before operating machine further.

Always disconnect machine from power when

investigating or correcting potential problems.

9. Rotate speed-control knob all the way

counterclockwise.

Test.Run

TWIST

To reset switch,

twist button

clockwise.

Figure.22.

Resetting the switch.

Serious. injury. or. death. can. result.

from. using. this. machine. BEFORE.

understanding. its. controls. and. related.

safety.information..DO.NOT.operate,.or.

allow.others.to.operate,.machine.until.

the.information.is.understood..

DO. NOT. start. machine. until. all.

preceding.setup.instructions.have.been.

performed..Operating.an.improperly.set.

up. machine. may. result. in. malfunction.

or. unexpected. results. that. can. lead.

to. serious. injury,. death,. or. machine/

property.damage.

Once assembly is complete, test run the machine to

ensure it is properly connected to power and safety

components are functioning properly.

If you find an unusual problem during the test run,

immediately stop the machine, disconnect it from power,

and fix the problem BEFORE operating the machine again.

The

Troubleshooting

table in the

SERVICE

section of this

manual can help.

Содержание W1866





























































Результаты поиска

Содержание W1866

Отзывы:

Похожие инструкции для W1866

Бренды по названию

Популярные бренды

Woodstock W1866, Руководство пользователя

Результаты поиска

Содержание W1866

Отзывы:

Похожие инструкции для W1866

Бренды по названию

Популярные бренды