Woodland Mills WC68 PTO Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 51

background image

WC68 Operator’s Manual

TOOL USE AND CARE

•

Always be sure the operator is familiar

with proper safety precautions and operation

techniques before using machine.

•

Do not force the tool.

Tools do a better and safer job when used in the manner for which

they are designed.

•

Turn off the tractor engine

and disconnect the PTO shaft before servicing, adjusting,

installing accessories or attachments, or storing. Such preventive safety measures reduce
the risk of starting the power tool accidentally.

•

Storing the wood chipper.

When the wood chipper is not in use, store it in a dry, secure

place or keep it well covered and out of reach of children. Inspect the wood chipper for good
working condition prior to storage and before re-use.

•

Maintain your wood chipper.

It is recommended that the general condition of the wood

chipper be examined before it is used.  Keep your wood chipper in good repair by adopting a
program  of  conscientious  repair  and  maintenance  in  accordance  with  the  recommended
procedures found in this manual.  If abnormal vibration or noise occurs, turn the wood chipper
off immediately and have the problem corrected before further use.

•

Keep blades sharp and clean.

Properly maintained wood chipper blades are less likely to

bind and make feeding-in brush easier.

•

Cleaning and Lubrication.

Use only soap and a damp cloth to clean your wood chipper.

Many household cleaners are harmful to plastic and rubber components on the wood chipper.

•

Use only accessories that are recommended

by the manufacturer for your model.

Suitable accessories for another wood chipper may create an injury risk when used on this
wood chipper.

•

Always

operate the machine with all safety devices and guards in place and in working order.

DO NOT modify or make changes to safety devices. DO NOT operate the machine if any
safety devices or guards are missing or inoperative.

•

Never leave wood chipper running unattended.

•

Never use the equipment to chip brush with trunks exceeding 6” (152 mm) in diameter

or for any purpose other than chipping brush as described in this manual.

WC68-MY2019: Rev A

Page of

8

49

27-Sep-2018

«
...
7
8
9
10
11
...
»

Содержание WC68 PTO




















































Отзывы:

Нет отзывов

Похожие инструкции для WC68 PTO

Бренд: Wacker Neuson Страницы: 54

Бренд: Jarvis Страницы: 12

Бренд: Alemite Страницы: 66

Бренд: Cherry Страницы: 10

Бренд: Wolf Garten Страницы: 198

Бренд: Fein Страницы: 58

Бренд: Fein Страницы: 30

MINI CARVER MIN.FG.600.60

Бренд: Arbortech Страницы: 76

Бренд: Roach Conveyors Страницы: 19

Бренд: Kaindl Страницы: 10

Бренд: Daewoo Страницы: 14

Бренд: Cembre Страницы: 60

Cherokee WARRIOR PA-28-151

Бренд: Piper Aircraft Corporation Страницы: 108

CERTI-CRIMP II 2381707-1

Бренд: TE Connectivity Страницы: 6

POWER TOOLS SNA9821

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 4

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды