manualshive.com logo in svg

Wood Stone MOUNTAIN CE Series, Руководство по обслуживанию

Поделиться
Скачать
Wood Stone MOUNTAIN CE Series Скачать руководство пользователя страница 17

Mountain Series CE Models 

Service Manual

 

PG 

17 

OF

 36

M0012.02  MAY 2017

An ongoing program of product improvement may 
require us to change specifications without notice. 

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226  USA

TOLL FREE

 800.988.8103

TEL

 360.650.1111

FAX

 360.650.1166

E-MAIL

 

[email protected]

woodstone-corp.com

GAS BURNER TROUBLESHOOTING

If the green light is OFF:

 With the oven ON Check for 24 VAC between TH and 

TR terminals on the ICS-2 Module at the rear of the oven� If there is 24 VAC then 
the ICS-2 Module is bad�

If there is not 24 VAC present:

 Check that Module is wired according to the 

schematic on the oven� Check wiring connections in the front Junction Box on the 
Transformer Plate and at the terminal strip on the Touchpad Control Board� With 
the oven on check for 24 VAC between the brown and white wires at the terminal 
strip on the back of the Control Board� If there is no voltage and the Controller is 
on, turn OFF the power supplying the oven� Disconnect all wires from the Control 
Board terminal strip EXCEPT pink, white and brown� Repower the oven, turn the 
control back on� If 24 VAC now present, check remaining wiring� Especially make 
sure that Thermocouple wiring is not shorted to ground� If 24 VAC is still not 
present-replace the Control Board�
Light on ICS Module is flashing - Module has timed out� Turn the oven OFF, 
then back on to reset� If there is no spark at the Burner follow the steps on the 
previous page to troubleshoot the problem� If there is spark proceed to the next 
step below� Replace the Module if it does not reset�

Symptom

Cause and/or Solution

< Continued from previous page

Burner does not light, oven Controller is 
on, no spark at the Burner�

Note: 

On any call where the complaint 

is that the Radiant Burner will not light, 
stay lit or is going out intermittently, 
Wood Stone strongly recommends that 
the Radiant Burner be removed for 
inspection and cleaning� The majority 
of Radiant Burner problems can be 
traced to debris in the Burner� See the 
“Common Repair Procedures” section of 
this manual�

Burner does not light, there is spark 
at the Burner� Dome Flame Indicator 
Lighton Controller is not lit� 

1.

 

Gas supply to the oven has been turned OFF� Check manual shutoffs, fire 
suppression system resets, etc� 

2.

 

There may be air in the gas line� On a new oven start-up there may be air in 
the gas line� Turn the oven ON for about 30 seconds� Turn it back OFF and 
then back ON for 30 seconds� Repeat this up to five times� If oven does not 
light and you are not smelling gas continue with this step, it will be necessary 
to remove the inlet plug on the Gas Valve which will enable the air to be bled 
more quickly from the line� This can be done on the IR Gas Valve if equipped� 
Remove the plug on the inlet side of the Gas Valve using a hex key wrench� 
Allow the air to bleed out until you smell gas� Re-install the plug� Allow the 
gas to dissipate and then turn the oven ON� If the oven does not light after 
30 seconds, turn it OFF and back ON again� It may be necessary to do this 
a few times� 

EXTINGUISH ALL OPEN FLAMES BEFORE BLEEDING THE GAS 

LINE. DO NOT LEAVE THE OVEN UNATTENDED WHILE THE INLET PLUG IS 
REMOVED FROM THE Gas Valve!

3.

 

Check for loose wire connections at the ICS Module and the Gas Valve�

Continued on next page >

RADIANT FLAME BURNER TROUBLESHOOTING (CONTINUED)

Содержание MOUNTAIN CE Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды