manualshive.com logo in svg

Wood Stone MOUNTAIN CE Series, Руководство по обслуживанию

Поделиться
Скачать
Wood Stone MOUNTAIN CE Series Скачать руководство пользователя страница 14

Mountain Series CE Models 

Service Manual

 

PG 

14 

OF

 36

M0012.02  MAY 2017

An ongoing program of product improvement may 
require us to change specifications without notice. 

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226  USA

TOLL FREE

 800.988.8103

TEL

 360.650.1111

FAX

 360.650.1166

E-MAIL

 

[email protected]

woodstone-corp.com

CONTROLLER TROUBLESHOOTING

Temperature display reads “open”

Indicates an open Thermocouple� Check for continuity between the 2 
Thermocouple leads� Verify that there is no continuity to ground� Check for 
loose Thermocouple connections at the Control Board and at the J-box on the 
Transformer Plate below the oven before replacing� If there is heat damage to 
the Thermocouple it is usually caused by excessive airflow beneath the oven that 
blows the heat from the IR back onto the Thermocouple wire� This needs to be 
corrected—call your local distributor�

Oven does not turn on, control is blank

Is the breaker and/or wall switch supplying power to the oven on?
Has one of the fuses blown?
The two fuses are located on the transformer box on the Transformer Plate 
located beneath the oven� Turn off the power supplying the oven before removing 
the fuses� If a fuse is blown, find and correct the short and replace the fuse 
with one of the same rating� 

In addition to a bad Gas Valve, wiring etc., a 

Thermocouple that is grounding out can also cause the breaker to trip. 
Note: A power surge or brown out condition may also cause a  fuse to fail.

Check for 24 VAC between the pink and the white wires at the terminal block on 
the oven Control Board inside the control box� If 24 VAC is present, make sure 
that the four nuts attaching the circuit board to the face of the box are tight� 

DO 

NOT OVERTIGHTEN

; they should be snug enough that pressure on the touch pad 

activates the switches on the circuit board�
If the Controller is still not coming on, carefully remove all wires except the pink 
and white from the circuit board terminal block� If the Controller comes on, it 
is OK but there is a defective component or damaged and/or incorrect wiring 
elsewhere� If with just the pink and white wires connected (and 24 VAC present), 
the Controller still does not come on, replace the Controller circuit board�
Disconnect incoming power before removing wires to prevent damage to the 
Control Board�

GAS OVEN TROUBLESHOOTING

PART 1-CONTROLLERS

TOUCHPAD CONTROLLERS

All versions of this Controller use a Lexan Touchpad (overlay) on the face of the control to operate the unit� It has Power and Flame 
Indicator lights and a Hearth Temperature display� IR equipped ovens will also have a Hearth Set Point display and adjustment arrows� 
Additional information can be found in the Oven Components-Oven Controllers section of this manual�

Symptom

Cause and/or Solution

Содержание MOUNTAIN CE Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды