manualshive.com logo in svg

Wood Stone MOUNTAIN CE Series, Руководство по обслуживанию

Поделиться
Скачать
Wood Stone MOUNTAIN CE Series Скачать руководство пользователя страница 16

Mountain Series CE Models 

Service Manual

 

PG 

16 

OF

 36

M0012.02  MAY 2017

An ongoing program of product improvement may 
require us to change specifications without notice. 

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226  USA

TOLL FREE

 800.988.8103

TEL

 360.650.1111

FAX

 360.650.1166

E-MAIL

 

[email protected]

woodstone-corp.com

GAS BURNER TROUBLESHOOTING

Symptom

Cause and/or Solution

OPERATIONAL OVERVIEW

Wood Stone CE gas ovens utilize a spark to Pilot ignition system� 
Flame rectification is sensed through the flame rod on the Pilot/Igniter 
to ground via the Pilot Tube� Each Burner has its own ignition (ICS) 
Module and Gas Valve� When the ICS Module receives 24 VAC power, 
it sends spark to the Igniter and opens the Pilot solenoid on the Gas 
Valve� When the Module senses flame rectification at the Pilot it will 
then power the main solenoid in the Gas Valve causing the Burner to 
fire� If the Pilot goes out, the ICS will automatically attempt to relight 
the Pilot� If the green light on the ICS is lit, the Module is receiving 
power� A flashing green light means the Module has timed out while 
trying to light the Pilot� Turn the oven OFF, then back on, to reset the 
Module�

RADIANT FLAME BURNER TROUBLESHOOTING

The Radiant Flame Burner is the Burner located at the rear of the oven� On some models, this Burner is located on the side of the 
oven chamber� It is the main heat source for all ovens equipped with this Burner� The flame height is adjustable by means of the 
Throttle Control Valve located on the front of the oven on the left side�

Burner does not light, oven Controller is 
on, no spark at the Burner�

Note: 

On any call where the complaint 

is that the Radiant Burner will not light, 
stay lit or is going out intermittently, 
Wood Stone strongly recommends that 
the Radiant Burner be removed for 
inspection and cleaning� The majority 
of Radiant Burner problems can be 
traced to debris in the Burner� See the 
“Common Repair Procedures” section of 
this manual�

When the oven is on the green light on the ICS-2 Module should be lit� This Module 
is located beneath the oven and mounted at the rear�

If the green light is on

 (light may start blinking after few minutes): Turn the oven 

OFF� Remove the rear Burner and remove any debris on the Burner� (See the 
“Common Repairs” section of this manual�) Check the Igniter wire for continuity 
between the terminal on the end and the spark electrode on the Igniter� Check the 
Igniter for damage (cracked insulator, bent or broken electrode, etc�)� Make sure 
electrode is not shorted to ground� Replace Igniter if damaged� Clean the spark 
electrode if needed�

If Igniter is fine: 

With the oven OFF remove the Igniter wire from the ICS Module� 

Turn the oven back on� Keep away from the Igniter terminal on the Module� You 
should hear a repetitive clicking sound coming from the Module� If no sound is 
heard replace the Module� If the ICS Module is bad check both Solenoid Coils on the 
Gas Valve for continuity� Make sure there are no shorts to ground on the valve�

Continued on next page >

Radiant Flame Burner

Pilot Tube

Gas Pipe

Burner 

housing

Flame 

jet

Pilot/Igniter

Содержание MOUNTAIN CE Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды