Wood-mizer TVSE11S - SC Скачать руководство пользователя страница 9

Страница: 9 / 120

SAFETY

Check the Machine Before Operation

Safety

MHdoc031116

1-4

Check the Machine Before Operation

DANGER!

Make sure all guards and covers are in place and secured

before operating the machine. Failure to do so may result in serious
injury.

WARNING!

Fasten the machine to the floor before operating.

IMPORTANT!

The machine’s operator should get training in operation

and adjustment of the machine.

Keep Persons Away

DANGER!

Keep all persons out of the path of moving equipment and

lumber when operating the machine. Failure to do so will result in
serious injury.

DANGER!

Always be sure all persons are out of the path of the blade

before starting the motor. Failure to do so will result in serious injury.

WARNING!

Allow blade to come to a complete stop before opening

the blade housing cover. Failure to do so will result in serious injury.

Содержание TVSE11S - SC

























































































































Результаты поиска

Содержание TVSE11S - SC

Отзывы:

Бренды по названию

Популярные бренды

Wood-mizer TVSE11S - SC, Руководство пользователя

Результаты поиска

Содержание TVSE11S - SC

Отзывы:

Бренды по названию

Популярные бренды