Wood-mizer TVSE11S - SC Скачать руководство пользователя страница 11

Страница: 11 / 120

SAFETY

Keep Safety Labels In Good Condition

Safety

MHdoc031116

1-6

WARNING!

Consider all electrical circuits energized and dangerous.

WARNING!

Disconnect and lock out power supply before servicing!

Failure to do so may result in serious injury.

WARNING!

Never assume or take the word of another person that the

power is off; check it out and lock it out.

WARNING!

Do not wear rings, watches, or other jewelry while working

around an open electrical circuit.

WARNING!

Remove the blade before performing any service to the

motor. Failure to do so may result in serious injury.

DANGER!

The operator must not for any reason perform any laser

maintenance or repair work.

DANGER!

Never clean the blade or the blade wheels using a brush

or a scraper whilst the blade is in motion.

CAUTION!

Before installation of the blade, inspect it for damage and

cracks. Use only properly sharpened blades. Always handle the blade
with extreme caution. Use suitable carrier equipment for transporting
the blades.

IMPORTANT!

No exchange with a different type of laser is permitted,

that no additional optical equipment shall be used.

Keep Safety Labels In Good Condition

IMPORTANT!

Always be sure that all safety decals are clean and

readable. Replace all damaged safety decals to prevent personal
injury or damage to the equipment. Contact your local distributor, or
call your Customer Service Representative to order more decals.

IMPORTANT!

If replacing a component which has a safety decal

affixed to it, make sure the new component also has the safety decal
affixed.

Содержание TVSE11S - SC

























































































































Результаты поиска

Содержание TVSE11S - SC

Отзывы:

Бренды по названию

Популярные бренды

Wood-mizer TVSE11S - SC, Руководство пользователя

Результаты поиска

Содержание TVSE11S - SC

Отзывы:

Бренды по названию

Популярные бренды