Wood-mizer Titan WB2000-EC Скачать руководство пользователя страница 22

Страница: 22 / 94

Sawmill Operation

Control Box Overview

3-2

EGdoc013119

Operation

Main Switch:

Disconnects/connects power to all electrical circuits.

Control Box Guard:

Protect operator from wood chips. Keep the control box guard clean. If control box

guard is damaged, replace it immediately Do not operate the sawmill without control box guard!

Patrz rysunek 3-2.

The control box includes controls to start and stop the machine. It also contains the

touch screen used to set up the machine and diagnose problems.

Emergency Stop:

Push the emergency stop button to stop the machine. It stops also the power feed,

up/down system and blade motor. Turn the emergency stop button clockwise to release the stop.

Touch screen:

The touch screen is used to setup the sawmill functions, controls the setworks and

diagnose problems. Upon initial power-up, the screen will display the Home Screen.

Setworks Controller Buttons (A, B, C, D):

The Setworks Controller Buttons are described in Section

4.2.

See Section 4.2

Oiling System switch with control light:

Turns on and off the blade oiling system. The light is on when

the system is working.

Lube System switch with control light:

Turns on and off the blade lube system. The light is on when

the system is working. OFF position - system is off. CONTINUOS position - delivers a steady stream of
lubricant. PULSE position - Use knob to adjust the desired flow rate.

RYS. 3-2

WB2000ec_006
713666_manual_oper

Touch screen

Emergency Stop

Setworks buttons (A, B,

C, D)

Oiling System switch

with control light

Lube System switch

with control light

Power Feed

Switch

Up/Down Switch

Feed Rate
Adjustment Knob

Debarker Arm Control

Switch

Key Switch

Board Removal Plate

Switch

Blade Start Button

Blade Guide
Switch

Debarker blade switch wit

control light

Laser indicator switch with

control light

Control Lights

Diagnostic Lights

Содержание Titan WB2000-EC































































































Результаты поиска

Содержание Titan WB2000-EC

Отзывы:

Похожие инструкции для Titan WB2000-EC

Бренды по названию

Популярные бренды

Wood-mizer Titan WB2000-EC, Руководство пользователя

Результаты поиска

Содержание Titan WB2000-EC

Отзывы:

Похожие инструкции для Titan WB2000-EC

Бренды по названию

Популярные бренды