manualshive.com logo in svg
  • Главная
  • /
  • Wood-mizer
  • /
  • BMS25
  • /
  • Инструкция по безопасности, эксплуатации, техническому обслуживанию и запасным частям.

Wood-mizer BMS25, Инструкция по безопасности, эксплуатации, техническому обслуживанию и запасным частям.

Поделиться
Скачать
Wood-mizer BMS25 Скачать руководство пользователя страница 44

Blade Installation

5-4

WM doc 1/20/21

5

 b. 

Slide the turnbuckle assembly off the head. 

 c. 

Rotate the sharpener head back so that it rests in the most upright position.

 d. 

Lift the indexing arm.

CAUTION!

 When disconnecting or reattaching the sharpener head, be 

sure to keep it supported. Do not allow the sharpener to fall. It may 
damage the grinding wheel or the blade, and may cause personal 
injury.

6.

Press the blade between the clamping plates.

7.

Lower the indexing arm.

8.

Reposition the sharpener head by replacing the wing nut that attaches the top rod end to
the motor mount.

9.

Make final adjustments to the blade support arms and guide assemblies to assure that
the blade band rests evenly on both the right and left hardened dowel pins located in the
blade clamp assembly.

NOTE: 

The blade should not touch the bottom of either side guide 

assembly.

NOTE: 

All three guide assemblies should lean slightly in the direction 

the blade travels through them.

Содержание BMS25




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды