background image

4

Remove the wok orifice assembly from the unit.

WOK ORIFICE ASSEMBLY INSTALLATION

Install the Wok Orifice Assembly

1

Place the wok orifice assembly over the wok elbow.

2

Tighten the set screw on the side of the wok orifice holder.

3

Connect the gas line to the wok orifice assembly.

BURNER GRATE REMOVAL

Remove the Burner Grate

Lift the burner grate from the unit.

BURNER GRATE INSTALLATION

Install the Burner Grate

Place the burner grates onto the unit.

BURNER CAP REMOVAL

To remove the burner cap, first remove:

1

Burner grate

Remove the Burner Cap

Lift the burner cap from the burner assembly.

BURNER CAP INSTALLATION

Install the Burner Cap

Place the burner cap onto the burner assembly.

ISLAND TRIM REMOVAL

To remove the island trim, first remove:

1

Flat wok grate

2

Wok grate

3

Wok top plate

4

Burner grates

5

Burner caps

Then, 

uninstall the unit

.

Remove the Island Trim

1

Use a Phillips screwdriver to remove the screws from the
island trim.

Sealed Burner Rangetop with Wok Service

Manual

Component Removal and Installation

REMOVE THE WOK ORIFICE ASSEMBLY (continued)

service.subzero.com

828990 REV. A     

11

 

Содержание Rangetop






























Отзывы: