manualshive.com logo in svg

Wolf E Series, Руководство по обслуживанию

Поделиться
Скачать
Wolf E Series Скачать руководство пользователя страница 50

Page 50

Error Code

Error

Possible Cause

Test/Action

E15/A1

Maximum operating

time exceeded.

The cooking mode is

canceled if the unit is

not being operated.

Temperature

determines the

maximum operating

time.

Instruct customer on operating times:

▪

Cavity temperature < 212ºF: not canceled.

▪

Cavity temperature 212ºF - 302ºF: Canceled in 48

hours.

▪

Cavity temperature 302ºF - 392ºF: Canceled in 20

hours.

▪

Cavity temperature 392ºF - 572ºF: Canceled in 10

hours.

▪

Cavity temperature > 572ºF: Canceled in five

hours.

E16/A1

Maximum hold time

exceeded.

An operation is put on

hold if waiting for

operator input.

Example: door is open,

or water tank needs

filling.

Instruct customer on maximum hold times. Exceeding

the maximum hold time cancels the operation.

▪

Operating mode: One hour.

▪

Programs and recipes: Three hours.

E17/F1

Food probe

temperature short

circuit.

Food probe, food

probe socket, or wiring

issue.

1

Verify that the food probe is not too hot.

2

Measure the resistance of the food probe.

3

Verify the insulation foil is not touching the socket.

4

Replace the control board.

E18/F1

Food probe

temperature open

circuit.

Open circuit in food

probe wires.
Loose or broken wire

or contact in food

probe socket.

1

Plug in the food probe.

2

Measure the resistance on the X4 connector

between X4-2 and X4-3.

3

Replace the food probe.

4

Replace the food probe socket.

5

If error occurs during heating, replace the food

probe socket.

6

Replace the control board.

E19/F28

Door lock not opening. Cavity temperature is >

572ºF.
Door lock defective.
Temperature sensor

open circuit or

interrupted.

1

Verify the cavity temperature.

2

Measure resistance of the temperature sensor.

3

External TCO tripped.

4

Replace the relay board.

E20/F28

Door lock not closing.

Defective door lock or

relay board.

1

Replace the door lock.

2

Replace the relay board.

E25/F3

Short circuit of

temperature sensor

300C.

1

Measure the resistance of temperature sensor

300C.

2

Replace the temperature sensor 300C.

3

Replace the relay board.

E26/F3

Open circuit in

temperature sensor

300C.

1

Measure resistance of the temperature sensor

300C.

2

Replace the temperature sensor 300C.

3

Replace the relay board.

E27/F17

Over temperature in

temperature sensor

300C.

Temperature limit of

the temperature sensor

300C exceeded.
Excessively warm air

flowing over the

temperature sensor

300C during self-clean

from a bad door

gasket.

1

Measure the resistance of the temperature sensor

300C.

2

Verify the room air fan operates at low, medium,

and high temperatures.

3

Replace the temperature sensor 300C.

4

Replace the door gasket.

E Series SO24 (SWS 13543126)

Troubleshooting

Troubleshooting Guide 

service.subzero.com

827705 REVA     01/2019

49

 

Содержание E Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды