WIRTH OKTOPUS GLASS-Jack GL-N 300 Скачать руководство пользователя страница 10

Страница: 10 / 27

O p e r a t i n g M a n u a l

OKTOPUS

GLASS-Jack

GL-N 400/300

Technical Documentation

BA 000 180_OA

Page 10 of 22

TOPUS

GLASS-Jack GL-N 400/300 amounts to < 70 dB (A), vibrations are < 2,5 m/s

which means that special protective measures are not required.
Operating restrictions result from the limited Working Load Limit of the OKTOPUS

GLASS-

Jack GL-N 400/300 (see section 2.3 Symbols and markings) as well as the performance da-

ta, the operating conditions of the used crane and the conditions of the construction site. Fur-

thermore, you have to regard the fact that the manipulated elements have to have sufficient

inherent stability and are suitable to be installed with a vacuum lifting device (if necessary

consult with the manufacturer of the elements).
Due to the broad variety of elements with many different surface coatings offered on the

market we cannot assume liability in case of possible material incompatibilities between suc-

tion rubber and surface coating.
The maximum Working Load Limit stipulated on the OKTOPUS

only applies to the use of

the original suction pads and a working height of maximum 400 m above sea level. Employ-

ing the OKTOPUS

in heights above 400 m leads to a decreased Working Load Limit of the

OKTOPUS

on the one hand, on the other hand the OKTOPUS

control system needs to be

adjusted. If you want to employ the OKTOPUS

in heights above 400 m, please contact the

Wirth Service Team beforehand.

When operating the OKTOPUS

at heights above 400 m the Working Load

Limit is reduced! The Working Load Limits stipulated on the OKTOPUS

and in this operating manual do not apply in this case!

Never perform any unauthorized adjustments at the control system of the

OKTOPUS

; this may lead to severe malfunction of the device! Danger to

limb and life! Consult with the OKTOPUS

manufacturer if it is necessary to

adjust the control system of the OKTOPUS

, e.g. to perform a height ad-

justment.

2.6 Transport and storage

The OKTOPUS

may only be moved with a suitable hoist/means of transport with appropri-

ate Working Load Limit.

For transport purposes take the OKTOPUS

out of operation by sliding the

switch “Suction/Release” to position “Release”!

Protect the rubber lip of the suction pads with protective cowls from dirt

and damage!

In order to avoid damage due to deep discharge the batteries during stor-

age, the OKTOPUS

has to be charged at least every two weeks.

Содержание OKTOPUS GLASS-Jack GL-N 300




























Результаты поиска

Содержание OKTOPUS GLASS-Jack GL-N 300

Отзывы:

Похожие инструкции для OKTOPUS GLASS-Jack GL-N 300

Бренды по названию

Популярные бренды

WIRTH OKTOPUS GLASS-Jack GL-N 300, Руководство по эксплуатации

Результаты поиска

Содержание OKTOPUS GLASS-Jack GL-N 300

Отзывы:

Похожие инструкции для OKTOPUS GLASS-Jack GL-N 300

Бренды по названию

Популярные бренды