WIRTH OKTOPUS GLASS-Jack GL-N 300 Скачать руководство пользователя страница 7

Страница: 7 / 27

O p e r a t i n g M a n u a l

OKTOPUS

GLASS-Jack

GL-N 400/300

Technical Documentation

BA 000 180_OA

Page 7 of 22

(21) Never employ the OKTOPUS

explosive areas or in the area of aggressive me-

dia!

(22)

Never

attempt to

lift damaged glass or façade elements!

(23)

Do not lift

the load

higher than necessary

(24)

Always

wear suitable protective clothing, helmets, gloves and safety shoes!

(25)

Never

leave the lifted load unsupervised!

(26)

Never lift more than one

glass or façade element at a time!

(27) Comply with the stipulated

maintenance information

•

daily visual and functional inspection

(battery’s charge level, vacuum gauges,

suction pads, alarm buzzer, control panel!

•

depending on the operating conditions,

but at least annually,

inspection by an ex-

pert!

(28) Never modify the OKTOPUS

in a way that safety is impaired.

Otherwise the manu-

facturer’s warranty will be void!

(29) Do not remove information signs, safety signs and inspection tags and plates from the

OKTOPUS

Otherwise the manufacturer’s warranty will be void!

2.3 Symbols and markings

Signal word

Meaning

Consequences of non-compliance

Warns of imminent

threat of danger

Death or serious injury or substantial

material damage as consequence.

Warns of potential

threat of danger

Death or serious injury or substantial

material damages are possible.

Warns of possibly

dangerous situation

Light injury or material damages are

possible.

Next to the type plate the following safety-related signs and pictographs are attached to the

OKTOPUS

(Inspection card)

(Working Load Limit OKTOPUS

)

(Before operating, read and comply

with operating manual as well as

safety instruction!)

(General information / Warning signs)

Содержание OKTOPUS GLASS-Jack GL-N 300




























Результаты поиска

Содержание OKTOPUS GLASS-Jack GL-N 300

Отзывы:

Похожие инструкции для OKTOPUS GLASS-Jack GL-N 300

Бренды по названию

Популярные бренды

WIRTH OKTOPUS GLASS-Jack GL-N 300, Руководство по эксплуатации

Результаты поиска

Содержание OKTOPUS GLASS-Jack GL-N 300

Отзывы:

Похожие инструкции для OKTOPUS GLASS-Jack GL-N 300

Бренды по названию

Популярные бренды