WireTech 5000P-10x Скачать руководство пользователя страница 9

Страница: 9 / 28

are connected well, then power can be applied to the device. The main socket and fuse are

located at the rear panel of the device.

When the device is powered on, verify that the display shows the following message:

Digital TV Processor (factory default unit-name)

IP: 10.10.60.148 (factory default IP Address for LAN access)

If no message is shown in the display or there is not light in the display, the device is

defective and has to be returned for servicing.

4. Navigating the Front Panel

POWER

Power indicator, green light means power is OK

TUNER LOCK

Tuner lock indicator, green light means signal is locked; if

there is no light, which means no signal input or wrong

parameters setting.

ALARM

Alarm indicator

LCD

2 × 20 character LCD

Operation buttons

〔〕〔〕〔〕〔〕〔

ENTER

〕〔

EXIT

〕

buttons

〔

〕〔

〕

are used to up/down pages of menu or

increase/decrease value when edit numbers

〔〕〔〕

are used to move cursor

〔

ENTER

〕

is used to enter sub menu or confirm operation

〔

EXIT

〕

is used to return previous menu or cancel operation

Common Interface

PCMCIA Module slot

5. Menu Structure and Operating the Device

The menu structure of the device is showed in below figure. After initialization is completed,

press

〔

ENTER

〕

button to enter main menu:

Main Menu

Inputs

Outputs

Ethernet

System

Содержание 5000P-10x





























Результаты поиска

Содержание 5000P-10x

Отзывы:

Бренды по названию

Популярные бренды

WireTech 5000P-10x, Руководство пользователя

Результаты поиска

Содержание 5000P-10x

Отзывы:

Бренды по названию

Популярные бренды