Winco W10000VE/A Скачать руководство пользователя страница 11

11

REV A

OMP-113

GENERATOR CARE

Proper care and maintenance of the generator is necessary to ensure 

a long trouble free life.

EXERCISING THE GENERATOR

The generator should be operated every three to four weeks. It should 

be operated for a period of time sufficient to warm the unit up and to 

dry out any moisture that has accumulated in the windings. If left, this 

moisture can cause corrosion in the winding. Frequent operation of the 

engine-generator set will also ensure that the set is operating properly 

should it be needed in an emergency.

GENERATOR MAINTENANCE

Any major generator service, including the installation or replacement 

of parts, should be performed only by a qualified electrical service 

technician. 

USE ONLY FACTORY APPROVED REPAIR PARTS.

  A. Bearing - The bearing used in these generators is a heavy duty, 

    double sealed ball bearing. They require no maintenance or 

  lubrication.

  B. Receptacles - Quality receptacles have been utilized. If a 

    receptacle should become cracked or otherwise damaged, 

    replace it. Using damaged or cracked receptacles can be both 

    dangerous to the operator and destructive to the equipment.

CLEANING

Remove dirt and debris with a cloth or brush. DO NOT use high 

pressure spray to clean either the engine or the generator. The high 

pressure spray could contaminate the fuel system and the generator 

components.

1. Keep the air inlet screen on both the engine and generator free of 

any dirt or debris to ensure proper cooling. At least yearly, remove 

the blower housing on the engine and clean the chaff and dirt out of 

the engine cooling fins and fly wheel. Clean more often if necessary. 

Failure to keep these areas clean may cause overheating and 

permanent damage to the unit.

2. Periodically clean muffler area to remove all grass, dirt, and 

combustible debris to prevent a fire.

3. On engine mufflers equipped with spark arresters, the spark arrester 

must be removed every 50 hours for cleaning and inspection. Replace 

if damaged.

RECEPTACLE PANEL WIRING DIAGRAM

G1

G2

G2

G2

G2

G2

GND

N

N

N

N

G2

G1

G1

G1

G1

GND

GND

N

N

G1

G1

G1

G1

G1

G1

G1

G1

G1

G1

G1

G1

G1

G1

G2

G2

N

N

N

N

N

N

N

N

N

GND

GND

GND

GND

GND

GND

N

G2

G2

G2

G2

G2

G2

G1

G1

40 AMP

TIME METER

Содержание W10000VE/A













Отзывы: